中国国家標準(GB,GB/T規格)
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) |  規格名称(英語) |
国際整合 |
|---|---|---|---|---|---|
| 25.100.30 | J05 | GB/T 145-2001 | 中心孔 | Center holes | IDT ISO 866:1975 |
| 25.010 | J52 | GB/T 158-1996 | 机床工作台 T形槽和相应螺栓 | Machine tool table--T-slots and corresponding bolts | EQV ISO 299-1987 |
| 25.160.40 | J04 | GB/T 324-1988 | 焊缝符号表示法 | Welds-symbolic representation on drawings | EQV ISO 2553-84 |
| 25.100.50 | J41 | GB/T 967-1994 | 螺母丝锥 | Nut taps | |
| 25.100.50 | J41 | GB/T 968-1994 | 丝锥螺纹公差 | Manufacturing tolerances on the threaded portion of taps | EQV ISO 2857/DAM1-84 |
| 25.100.50 | J41 | GB/T 969-1994 | 丝锥技术条件 | Technical specification for taps | NEQ ISO 8830-91 |
| 25.100.50 | J41 | GB/T 970.1-1994 | 圆板牙 型式和尺寸 | The types and dimensions for circular screwing dies | EQV ISO 2568-88 |
| 25.100.50 | J41 | GB/T 970.2-1994 | 圆板牙 技术条件 | Technical specifications for circular screwing dies | NEQ ISO 2568-88 |
| 25.100.50 | J41 | GB/T 970.3-1994 | 圆板牙架型式和互换尺寸 | Die stocks--Interchangeability dimensions | EQV ISO 2568-88 |
| 25.100.50 | J41 | GB/T 971-1994 | 滚丝轮 | Thread rolling cylindrical dies | |
| 25.100.50 | J41 | GB/T 972 -1994 | 搓丝板 | Thread rolling flat dies | |
| 25.160.20 | J33 | GB/T 983-1995 | 不锈钢焊条 | Stainless steel covered electrodes | NEQ ANSI/AWS A 5.4-92 |
| 25.160.20 | J33 | GB/T 984-2001 | 堆焊焊条 | Hardfacing electrodes for shielded metal arc welding | EQV ANSI/AWS A5.13 |
| 25.160.40 | J33 | GB/T 985-1988 | 气焊、手工电弧焊及气体保护焊焊缝坡口的基本形式与尺寸 | Basic forms and sizes of weld grooves for gas welding manual arc welding and gas-Shielded arc welding | |
| 25.160.40 | J33 | GB/T 986-1988 | 埋弧焊焊缝坡口的基本形式和尺寸 | Basic forms and sizes of weld grooves for submerged arc welding | |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.180 | K61 | GB/T 1020-1989 | 电渣重熔炉的试验方法 | Test methods for electro-slag remelting furnaces | EQV IEC 60779-83 |
| 25.100.20 | J41 | GB/T 1109-1985 | 短莫氏锥柄立铣刀 | End mills with short Morse taper shank | |
| 25.100.20 | J41 | GB/T 1112.1-1997 | 键槽铣刀 第1部分: 直柄键槽铣刀 型式和尺寸 | Slot drills- Part 1: Milling cutters with parallel shanks-Dimensions | EQV ISO 1641/I:1978 |
| 25.100.20 | J41 | GB/T 1112.2-1997 | 键槽铣刀 第2部分: 莫氏锥柄键槽铣刀 型式和尺寸 | Slot drills--Part 2: Milling cutters with Morse taper shanks-Dimensions | EQV ISO 1641-:Ⅱ:1978 |
| 25.100.20 | J41 | GB/T 1112.3-1997 | 键槽铣刀 第3部分: 技术条件 | Slot drills--Part 3: Technical specifications | |
| 25.100.20 | J41 | GB/T 1114.1-1998 | 套式立铣刀 第1部分: 型式与尺寸 | Shell end mills--Part 1: Dimensions | EQV ISO 2586:1985 |
| 25.100.20 | J41 | GB/T 1114.2-1998 | 套式立铣刀 第2部分: 技术条件 | Shell end mills--Part 2: Tachnical specifications | |
| 25.100.20 | J41 | GB/T 1115-1985 | 圆柱形铣刀 | Cylindrical cutters | NEQ ISO 2584-72 |
| 25.100.20 | J41 | GB/T 1117-1985 | 直齿三面刃铣刀 | Side and face milling cutter with straight teeth | NEQ ISO 2587-72 |
| 25.100.20 | J41 | GB/T 1118-1985 | 错齿三面刃铣刀 | Side and face milling cutters with double alternate helix | NEQ ISO 2587-72 |
| 25.100.20 | J41 | GB/T 1119-1985 | 尖齿槽铣刀 | Flat relieved tooth slotting cutters | NEQ ISO 2585-72 |
| 25.100.20 | J41 | GB/T 1124.1-1996 | 凸凹半圆铣刀 第1部分: 凹半圆铣刀的型式和尺寸 | Convex and concave milling cutters--Part 1: The types and dimensions for concave milling cutters | EQV ISO 3860-1976 |
| 25.100.20 | J41 | GB/T 1124.2-1996 | 凸凹半圆铣刀 第2部分: 凸半圆铣刀的型式和尺寸 | Convex and concave milling cutters--Part 2: The types and dimensions for convex milling cutters | EQV ISO 3860-1976 |
| 25.100.20 | J41 | GB/T 1124.3-1996 | 凸凹半圆铣刀 技术条件 | Convex and concave milling cutters technical specifications | EQV DIN 855/2-1981 |
| 25.100.20 | J41 | GB/T 1127-1997 | 半圆键槽铣刀 | Cutters for woodruff keyseats | |
| 25.100.30 | J41 | GB/T 1131-1984 | 手用铰刀 | Hand reamers | NEQ ISO 236/1-76 |
| 25.100.30 | J41 | GB/T 1132-1984 | 直柄机用铰刀 | Machine reamers with parallel shanks | NEQ ISO 521-75 |
| 25.100.30 | J41 | GB/T 1133-1984 | 锥柄机用铰刀 | Machine reamers with Morse taper shanks | NEQ ISO 521-75 |
| 25.100.30 | J41 | GB/T 1134-1984 | 带刃倾角锥柄机用铰刀 | Machine reamers with edge inclination Morse taper shanks | |
| 25.100.30 | J41 | GB/T 1135-1984 | 套式机用铰刀 | Shell machine reamers | NEQ ISO 2402-72 |
| 25.100.30 | J41 | GB/T 1139-1984 | 直柄莫氏圆锥和公制圆锥铰刀 | Morse and metric taper reamers with parallel shanks | NEQ ISO 2250-72 |
| 25.100.30 | J41 | GB/T 1140-1984 | 锥柄莫氏圆锥和公制圆锥铰刀 | Morse and metric taper reamers with Morse taper shanks | NEQ ISO 2250-72 |
| 25.100.30 | J41 | GB/T 1141-1984 | 锥柄扩孔钻 | Core drills with Morse taper shanks | NEQ ISO 7079-81 |
| 25.100.30 | J41 | GB/T 1142-1984 | 套式扩孔钻 | Shell drills | NEQ ISO 3314-75 |
| 25.100.30 | J41 | GB/T 1143-1984 | 60°、90°、120°锥柄锥面锪钻 | Countersinks with morse taper shanks for angles 60°,90°and 120°inclusive | NEQ ISO 3293-75 |
| 25.100.30 | J41 | GB/T 1438.1-1996 | 锥柄麻花钻 第1部分: 莫氏锥柄麻花钻的型式和尺寸 | Taper shank twist drills--Part 1: The types and dimensions for Morse taper shank twist drills | EQV ISO 235-1980 |
| 25.100.30 | J41 | GB/T 1438.2-1996 | 锥柄麻花钻 第2部分: 莫氏锥柄长麻花钻的型式和尺寸 | Taper shank twist drills--Part 2: The types and dimensions for long Morse taper shank drills | |
| 25.100.30 | J41 | GB/T 1438.3-1996 | 锥柄麻花钻 第3部分: 莫氏锥柄加长麻花钻的型式和尺寸 | Taper shank twist drills--Part 3: The types and dimensions for lengthened morse taper shank twist drills | |
| 25.100.30 | J41 | GB/T 1438.4-1996 | 锥柄麻花钻 第4部分: 莫氏锥柄超长麻花钻的型式和尺寸 | Taper shank twist drills--Part 4: The types and dimensions for extra-long Morse taper shank twist drills | EQV ISO/DIS 3291-93 |
| 25.140.30 | J41 | GB/T 1442-1985 | 直柄工具用传动扁尾及套筒的尺寸和公差 | Driving tenons and sockets for parallel shank tools-- Dimensions and tolerances | EQV ISO 4203-78 |
| 25.140.30 | J41 | GB/T 1443-1996 | 机床和工具柄用自夹圆锥 | Machine tools--Self-holding tapers for tool shanks | EQV ISO 296-1991 |
| 25.080.10 | J53 | GB/T 1582-1993 | 卧式车床 参数 | General purpose parallel lathes--Parameters | |
| 25.220.40 | H25 | GB/T 1838-1995 | 镀锡钢板(带)镀锡量试验方法 | Tin coated sheet(strip)--Tin coating mass testing method | EQV ISO 1111/1-1983 |
| 25.220.40 | H25 | GB/T 1839-1993 | 钢铁产品镀锌层质量试验方法 | Steel product--Zinc coating mass testing method | NEQ ISO 1460-73 |
| 25.160.40 | J33 | GB/T 1954-1980 | 铬镍奥氏体不锈钢焊缝铁素体含量测量方法 | Determination of the weldign seam iron element contentin chromium,nickel austenitic stainless steel | |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.100.01 | J41 | GB/T 2075-1998 | 切削加工用硬切削材料的用途 切屑形式大组和用途小组的分类代号 | Application of hard cutting materials for machining by chip removal--Designation of the main groups of chip removal and groups of application | IDT ISO 513-1991 |
| 25.100 | H70 | GB/T 2076-1987 | 切削刀具用可转位刀片型号表示规则 | Indexale inserts for cutting tools--Designation | EQV ISO 1832-85 |
| 25.100 | H72 | GB/T 2077-1987 | 硬质合金可转位刀片圆角半径 | Indexable hardmetal (carbide) inserts--Corner radii | EQV ISO 3286-77 |
| 25.100 | H72 | GB/T 2078-1987 | 带圆孔的硬质合金可转位刀片 | Indexable hardmetal (carbide) inserts with rounded corners, with cylindrical fixing hole | EQV ISO 3364-85 |
| 25.100 | H72 | GB/T 2079-1987 | 无孔的硬质合金可转位刀片 | Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole--Dimensions | EQV ISO 883-85 |
| 25.100 | H72 | GB/T 2080-1987 | 沉孔硬质合金可转位刀片 | Indexable hardmetal (carbide) inserts with rounded corners, with partly cylindrical fixing hole--Part 1: Dimensions of inserts with 7°normal clearance | EQV ISO 6987/1-83 |
| 25.100 | H72 | GB/T 2081-1987 | 硬质合金可转位铣刀片 | Indexable hardmetal (carbide)inserts with wiper edges, without fixing hole--Dimensions | EQV ISO 3365-85 |
| 25.100.70 | J43 | GB/T 2476-1994 | 普通磨料 代号 | Symbols of abrasive materials | |
| 25.100.70 | J43 | GB/T 2478-1996 | 普通磨料 棕刚玉 | Conventional abrasive--Brown fused alumina | |
| 25.100.70 | J43 | GB/T 2480-1996 | 普通磨料 碳化硅 | Conventional abrasive Wilicon carbide | |
| 25.100.70 | J43 | GB/T 2481.1-1998 | 固结磨具用磨料 粒度组成的检测和标记 第1部分: 粗磨粒 F4~F220 | Bonded abrasives--Determination and designation of grain size distribution--Part 1: Macrogrits F4 to F220 | EQV ISO 8486-1:1996 |
| 25.100.70 | J43 | GB/T 2481.2-1998 | 固结磨具用磨料 粒度组成的检测和标记 第2部分: 微粉F230~F1200 | Bonded abrasives--Determination and designation of grain size distribution--Part 2: Microgrits F230 to F1200 | EQV ISO 8486-2:1996 |
| 25.100.70 | J43 | GB/T 2483-1983 | 磨料标志和包装规定 | Marking and packing | |
| 25.100.70 | J43 | GB/T 2484-1994 | 普通磨具 代号和标记 | Symbols and designation for bonded abrasive products | NEQ ISO 525-86 |
| 25.100.70 | J43 | GB/T 2485-1997 | 普通磨具 砂轮 技术条件 | Bonded abrasive products Grinding wheel Technical specifications | |
| 25.100.70 | J43 | GB/T 2486-1997 | 普通磨具 磨头 技术条件 | Bonded abrasive products Mounted wheel Technical specifications | |
| 25.100.70 | J43 | GB/T 2487-2001 | 普通磨具 磨石 技术条件 | Bonded abrasive products Sticks Technical specifications | |
| 25.100.70 | J43 | GB/T 2488-2001 | 普通磨具 砂瓦 技术条件 | Bonded abrasive products Grinding segments Technical specifications | |
| 25.100.70 | J43 | GB/T 2489-1984 | 薄片砂轮 | Thin grinding wheels | |
| 25.100.70 | J43 | GB/T 2492-1984 | 砂轮静平衡检验方法及不平衡数值 | Static balance testing for grinding wheels and unbalance value | |
| 25.100.70 | J43 | GB/T 2493-1995 | 砂轮的回转试验方法 | Rotation test of grinding wheel strength | NEQ JIS R6240-1986 |
| 25.100.70 | J43 | GB 2494-1995 | 磨具安全规则 | Safety rules for bonded abrasives | NEQ ΓOCT 12.3.028-82 |
| 25.100.70 | J43 | GB/T 2495-1996 | 普通磨具 包装 | Packing for bonded abrasive products | NEQ ISO 2248-1985 |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.060.20 | J52 | GB/T 2554.1-1998 | 机械分度头 精度检验 | Mechanical dividing heads Testing of accuracy | EQV ISO 5734-1986 |
| 25.060.20 | J52 | GB/T 2554.2-1998 | 机械分度头 分类和技术条件 | Mechanical dividing heads Classifations and Technical specifcations | |
| 25.040.40 | N15 | GB/T 2612-1989 | DDZ-Ⅱ系列电动单元组合仪表工作信号 | DDZ-ⅡSeries process electronic control system operating signal | |
| 25.040.40 | N15 | GB/T 2613-1989 | DDZ-Ⅲ系列电动单元组合仪表工作信号 | DDZ-ⅢSeries process electronic control system operating signal | |
| 25.040.40 | N10 | GB/T 2625-1981 | 过程检测和控制流程图用图形符号和文字代号 | Prccess detection and control flow chart--Symbols and letter codes | |
| 25.160.40 | J33 | GB/T 2649-1989 | 焊接接头机械性能试验取样方法 | Methods of sampling for mechanical properties tests of welded joint | |
| 25.160 | J33 | GB/T 2650-1989 | 焊接接头冲击试验方法 | Method of impact test for welded joint | |
| 25.160.40 | J33 | GB/T 2651-1989 | 焊接接头拉伸试验方法 | Method of tensile test for welded joint | |
| 25.160.40 | J33 | GB/T 2652-1989 | 焊缝及熔敷金属拉伸试验方法 | Method of tensile tests for weld and deposited metal | |
| 25.160.40 | J33 | GB/T 2653-1989 | 焊接接头弯曲及压扁试验方法 | Methods of bend and compression tests for welded joint | NEQ ISO 5173-81 |
| 25.160.40 | J33 | GB/T 2654-1989 | 焊接接头及堆焊金属硬度试验方法 | Methods of hardness tests for welded joint and surfacing metal | |
| 25.160.40 | J33 | GB/T 2655-1989 | 焊接接头应变时效敏感性试验方法 | Method of strain-age sensibillity test for welded joint | |
| 25.160.40 | J33 | GB/T 2656-1981 | 焊缝金属和焊接接头的疲劳试验法 | Weld beads metal and welds--Fatigue tests | |
| 25.060.20 | J45 | GB/T 2804-1981 | 组合夹具元件结构要素 | Modular parts of fixture construction--General features, profiles and dimensions | |
| 25.080.40 | J54 | GB/T 2813-1989 | 台式钻床参数 | Bench drilling machines - Parameters | |
| 25.080.40 | J54 | GB/T 2814-1989 | 立式钻床参数 | Vertical drilling machines - Parameters | |
| 25.080.40 | J54 | GB/T 2815-1989 | 钻床主轴端部 | Drilling machines？Spindle noses | |
| 25.120.30 | J46 | GB/T 2851.1-1990 | 冲模滑动导向模架 对角导柱模架 | Sliding guide die sets for press tools？Diagonal pillar sets | |
| 25.120.30 | J46 | GB/T 2851.3-1990 | 冲模滑动导向模架 后侧导柱模架 | Sliding guide die sets for press tools - Back pillar sets | |
| 25.120.30 | J46 | GB/T 2851.4-1990 | 冲模滑动导向模架 后侧导柱窄形模架 | Sliding guide die sets for press tools - Back pillar sets (narrow) | |
| 25.120.30 | J46 | GB/T 2851.5-1990 | 冲模滑动导向模架 中间导柱模架 | Sliding guide die seta for press tools - Center pillar sets | |
| 25.120.30 | J46 | GB/T 2851.6-1990 | 冲模滑动导向模架 中间导柱圆形模架 | Sliding guide die sets for press tools - Center pillar sets (round) | |
| 25.120.30 | J46 | GB/T 2851.7-1990 | 冲模滑动导向模架 四导柱模架 | Sliding guide die sets for press tools - Four pillar die sets | |
| 25.120.30 | J46 | GB/T 2852.1-1990 | 冲模滚动导向模架 对角导柱模架 | Ball slide die sets for press tools - Diagonal pillar sets | |
| 25.120.30 | J46 | GB/T 2852.2-1990 | 冲模滚动导向模架 中间导柱模架 | Ball slide die sets for press tools - Center pillar sets | |
| 25.120.30 | J46 | GB/T 2852.3-1990 | 冲模滚动导向模架 四导柱模架 | Ball slide die sets for press tools - Four pillar die sets | |
| 25.120.30 | J46 | GB/T 2852.4-1990 | 冲模滚动导向模架 后侧导柱模架 | Ball slide die sets for press tools？Back pillar die sets | |
| 25.120.30 | J46 | GB/T 2855.1-1990 | 冲模滑动导向模座 对角导柱上模座 | Holder for sliding guide die sets for press tools - Punch holder for diagonal pillar sets | |
| 25.120.30 | J46 | GB/T 2855.2-1990 | 冲模滑动导向模座 对角导柱下模座 | Holder for sliding guide die sets for press tools - Die holder for diagonal pillar sets | |
| 25.120.30 | J46 | GB/T 2855.5-1990 | 冲模滑动导向模座 后侧导柱上模座 | Holder for sliding guide die sets for press tools - Punch holder for back pillar sets | |
| 25.120.30 | J46 | GB/T 2855.6-1990 | 冲模滑动导向模座 后侧导柱下模座 | Holder for ball slide die sets for press tools - Die holder for back pillar sets | |
| 25.120.30 | J46 | GB/T 2855.7-1990 | 冲模滑动导向模座 后侧导柱窄形上模座 | Holder for sliding guide die sets for press tools - Punch holder for back pillar sets (narrow) | |
| 25.120.30 | J46 | GB/T 2855.8-1990 | 冲模滑动导向模座 后侧导柱窄形下模座 | Holder for sliding guide die sets for press tools - Die holder for back pillar sets (narrow) | |
| 25.120.30 | J46 | GB/T 2855.9-1990 | 冲模滑动导向模座 中间导柱上模座 | Holder for sliding guide die sets for press tools - Punch holder for center pillar sets | |
| 25.120.30 | J46 | GB/T 2855.10-1990 | 冲模滑动导向模座 中间导柱下模座 | Holder for ball slide die sets for press tools - Die holder for center pillar sets | |
| 25.120.30 | J46 | GB/T 2855.11-1990 | 冲模滑动导向模座 中间导柱圆形上模座 | Holder for sliding guide die sets for press tools - Punch holder for center pollar sets (round) | |
| 25.120.30 | J46 | GB/T 2855.12-1990 | 冲模滑动导向模座 中间导柱圆形下模座 | Holder for sliding guide die sets for press tools - Die holder for center pillar sets (round) | |
| 25.120.30 | J46 | GB/T 2855.13-1990 | 冲模滑动导向模座 四导柱上模座 | Holder for sliding guide die sets for press tools - Punch holder for four pillar sets | |
| 25.120.30 | J46 | GB/T 2855.14-1990 | 冲模滑动导向模座 四导柱下模座 | Holder for ball slide die sets for press tools？Die holder for four pillar sets | |
| 25.120.30 | J46 | GB/T 2856.1-1990 | 冲模滚动导向模座 对角导柱上模座 | Holder for ball slide die sets for press tools - Punch holder for diagonal pillar sets | |
| 25.120.30 | J46 | GB/T 2856.2-1990 | 冲模滚动导向模座 对角导柱下模座 | Holder for ball slide die sets for press tools - Die holder for diagonal pillar sets | |
| 25.120.30 | J46 | GB/T 2856.3-1990 | 冲模滚动导向模座 中间导柱上模座 | Holder for ball silde die sets for press tools - Punch holder for center pillar sets | |
| 25.120.30 | J46 | GB/T 2856.4-1990 | 冲模滚动导向模座 中间导柱下模座 | Holder for ball slide die sets for press tools - Die holder for center pillar sets | |
| 25.120.30 | J46 | GB/T 2856.5-1990 | 冲模滚动导向模座 四导柱上模座 | Holder for ball slide die sets for press tools - Punch holder for four pillar sets | |
| 25.120.30 | J46 | GB/T 2856.6-1990 | 冲模滚动导向模座 四导柱下模座 | Holder for ball slide die sets for press tools - Die holder for four pillar sets | |
| 25.120.30 | J46 | GB/T 2856.7-1990 | 冲模滚动导向模座 后侧导柱上模座 | Holder for ball silde die sets for press tools - Punch holder for back pillar sets | |
| 25.120.30 | J46 | GB/T 2856.8-1990 | 冲模滚动导向模座 后侧导柱下模座 | Holder for ball slide die sets for press tools - Die holder for back pillar sets | |
| 25.120.30 | J46 | GB/T 2861.1-1990 | 冲模导向装置 A型导柱 | Guide unit for press tools - Guide pillars, types A | |
| 25.120.30 | J46 | GB/T 2861.2-1990 | 冲模导向装置 B型导柱 | Guide unit for press tools - Guide pillars, type B | |
| 25.120.30 | J46 | GB/T 2861.3-1990 | 冲模导向装置 C型导柱 | Guide unit for press tools - Guide pillars, type C | |
| 25.120.30 | J46 | GB/T 2861.4-1981 | 冷冲模导向装置 A型小导柱 | Guide unit of cold press dies--Small guide | |
| 25.120.30 | J46 | GB/T 2861.5-1981 | 冷冲模导向装置 B型小导柱 | Guide unit of cold press dies--Small guide pillars, type B | |
| 25.120.30 | J46 | GB/T 2861.6-1990 | 冲模导向装置 A型导套 | Guide unit for press tools - Guide bushes, type A | |
| 25.120.30 | J46 | GB/T 2861.7-1990 | 冲模导向装置 B型导套 | Guide unit for press tools - Guide bushes, type B | |
| 25.120.30 | J46 | GB/T 2861.8-1990 | 冲模导向装置 C型导套 | Guide unit for press tools - Guide bushes, type C | |
| 25.120.30 | J46 | GB/T 2861.9-1981 | 冷冲模导向装置 小导套 | Guide unit of cold press dies--Small guide bushing | |
| 25.120.30 | J46 | GB/T 2861.10-1990 | 冲模导向装置 钢球保持圈 | Guide unit for press tools - Cage | |
| 25.120.30 | J46 | GB/T 2861.11-1990 | 冲模导向装置 圆柱螺旋压缩弹簧 | Guide unit for press tools - Cylindrical coil compression spring | |
| 25.120.30 | J46 | GB/T 2861.12-1990 | 冲模导向装置 A型可卸导柱 | Guide unit for press tools - Guide pillar with taper lead, type A | |
| 25.120.30 | J46 | GB/T 2861.13-1990 | 冲模导向装置 B型可卸导柱 | Guide unit fir press tools - Guide pillar with taper lead, type B | |
| 25.120.30 | J46 | GB/T 2861.14-1990 | 冲模导向装置 衬套 | Guide unit for press tools - Bushing | |
| 25.120.30 | J46 | GB/T 2861.15-1990 | 冲模导向装置 垫圈 | Guide unit for press tools？Washer | |
| 25.120.30 | J46 | GB/T 2861.16-1990 | 冲模导向装置 压板 | Guide unit for press tools - Clampr | |
| 25.120.30 | J46 | GB/T 2861.17-1981 | 冷冲模导向装置 可卸导柱模座安装尺寸 | Guide unit of cold press dies--Mounting dimension of die holder for removable guide pillars | |
| 25.120.30 | J46 | GB/T 2861.18-1981 | 冷冲模导向装置 压圈固定导柱 | Guide unit of cold press dies--Guide pillars with ring fixed | |
| 25.120.30 | J46 | GB/T 2861.19-1981 | 冷冲模导向装置 压圈固定导套 | Guide unit of cold press dies--Guide bushing with ring fixed | |
| 25.120.30 | J46 | GB/T 2861.20-1981 | 冷冲模导向装置 压圈 | Guide unit of cold press dies--Clamping ring | |
| 25.220.40 | H25 | GB/T 2972-1991 | 镀锌钢丝锌层硫酸铜试验方法 | Zinc-coated steel wire - Test method for uniformity of zinc coating on wire by the copper sulphate dip | |
| 25.220.40 | H25 | GB/T 2973-1991 | 镀锌钢丝锌层重量试验方法 | Zinc-coated steel wire - Test method for weight of zinc coating | |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.100.70 | J43 | GB/T 3043-2000 | 棕刚玉化学分析方法 | Abrasive grains and crude--Chemical analysis of brown fused aluminium oxide | EQV ISO 9285:1997 |
| 25.100.70 | J43 | GB/T 3044-1989 | 白刚玉、铬刚玉 化学分析方法 | Chemical analysis methods for white fused alumina and pink fused alumina | |
| 25.100.70 | J43 | GB/T 3045-1989 | 碳化硅 化学分析方法 | Chemical analysis methods for silicon carbide | |
| 25.160.50 | H62 | GB/T 3131-2001 | 锡铅钎料 | Tin-lead solder | NEQ ISO 9453:1990 |
| 25.220.20 | A22 | GB/T 3138-1995 | 金属镀覆和化学处理与有关过程术语 | Terminology for metallic coating chemical treatment and related process | NEQ ISO 2079-81 |
| 25.080 | J50 | GB/T 3167-1993 | 金属切削机床 操作指示形象化符号 | Symbols for indications appearing on machine tools | NEQ ISO 7000-1984 |
| 25.040.20 | J50 | GB/T 3168-1993 | 数字控制机床 操作指示形象化符号 | Numerical control of machines--Symbols | NEQ ISO 2972-1979 |
| 25.140.01 | J48 | GB/T 3227-2000 | 螺栓螺母用装配工具 机动套筒工具的传动四方 | Assembly tools for screws and nuts-Driving squares for power socket tools | IDT ISO 1174-2:1996 |
| 25.140.01 | J48 | GB/T 3228-2000 | 螺栓螺母用装配工具 冲击式机动四方传动套筒的尺寸 | Assembly tools for screws and nuts-Machine-operated square drive sockets (impact)--Dimensions | NEQ ISO 2725-2:1996 |
| 25.140.01 | J48 | GB/T 3229-2000 | 螺栓螺钉用装配工具 机动螺刀头的六角传动端 | Assembly tools for bolts and screws--Hexagon drive ends for machine-operated screwdriver bits | EQV ISO 1173:1988 |
| 25.160.40 | J04 | GB/T 3323-1987 | 钢熔化焊对接接头射线照相和质量分级 | Methods for radiographic inspection and classification of radiographs for fusion welded butt joints in steel | |
| 25.040.40 | N10 | GB/T 3369-1989 | 工业自动化仪表用模拟直流电流信号 | Analogue direct current signals for industrial process measurement and control instruments | NEQ IEC 60381-2-1978 |
| 25.040.40 | N10 | GB/T 3370-1989 | 工业自动化仪表用模拟直流电压信号 | Analogue direct voltage signals for industrial process measurement and control instruments | NEQ IEC 60381-1-78 |
| 25.160 | J33 | GB/T 3375-1994 | 焊接术语 | Welding terminology | |
| 25.140 | J47 | GB/T 3390.1-1989 | 手动套筒扳手套筒 | Hand operated square drive socket | NEQ ISO 691-83 |
| 25.140 | J47 | GB/T 3390.2-1989 | 手动套筒扳手传动方榫和方孔 | Driving square for hand operated socket wrenches | |
| 25.140 | J47 | GB/T 3390.3-1989 | 手动套筒扳手传动附件 | Drivings parts for hand operated square drive socket wrenches | NEQ ISO 3315-75 |
| 25.140 | J47 | GB/T 3390.4-1989 | 手动套筒扳手连接附件 | Conjoining parts for hand operated square drive socket wrenches | NEQ ISO 3316-75 |
| 25.140 | J47 | GB/T 3390.5-1989 | 手动套筒扳手检验规则、包装与标志 | Inspection, packaging and marking for hand operated socket wrenches | |
| 25.160.20 | H44 | GB/T 3429-1994 | 焊接用钢盘条 | Wire rods for electrode | NEQ JIS G3503-80 |
| 25.100.50 | J41 | GB/T 3464.1-1994 | 机用和手用丝锥 | Machine and hand taps | EQV ISO 529-75 |
| 25.100.50 | J41 | GB/T 3464.2-1994 | 长柄机用丝锥 | Long shank machine taps | EQV ISO 2283-72 |
| 25.100.50 | J41 | GB/T 3464.3-1994 | 短柄机用和手用丝锥 | Short shank machine and hand taps | NEQ ISO 529-75 |
| 25.100.50 | J41 | GB/T 3506-1993 | 螺旋槽丝锥 | Machine taps with helical flutes | |
| 25.060 | J58 | GB/T 3668.1-1983 | 组合机床通用部件 多轴箱箱体和输入轴尺寸 | Modular units for machine tool construction--Multi-spindle heads--Casing and input drive shaft dimensions | EQV ISO 2912-73 |
| 25.060 | J58 | GB/T 3668.2-1983 | 组合机床通用部件 支架尺寸 | Modular units for machine tool construction--Support brackets--Dimensions | EQV ISO 3610-76 |
| 25.060 | J58 | GB/T 3668.3-1983 | 组合机床通用部件 回转工作台和回转工作台用多边形中间底座尺寸 | Modular units for machine tool construction--Rotary tables and multi-sided centre bases for rotary tables--Dimensions | EQV ISO 3371-75 |
| 25.060 | J58 | GB/T 3668.4-1983 | 组合机床通用部件 滑台尺寸 | Modular units for machine tool construction--Slide units--Dimensions | EQV ISO 2562-73 |
| 25.060 | J58 | GB/T 3668.5-1983 | 组合机床通用部件 动力箱尺寸 | Modular units for machine tool construction--Headstocks--Dimensions | EQV ISO 2727-73 |
| 25.060 | J58 | GB/T 3668.6-1983 | 组合机床通用部件 滑台侧底座尺寸 | Modular units for machine tool construction--Wing bases for slide units--Dimensions | EQV ISO 2769-73 |
| 25.060 | J58 | GB/T 3668.7-1983 | 组合机床通用部件 中间底座和立柱尺寸 | Modular units for machine tool construction--Centre bases and columns--Dimensions | EQV ISO 2891-77 |
| 25.060 | J58 | GB/T 3668.8-1983 | 组合机床通用部件 立柱侧底座尺寸 | Modular units for machine tool construction--Wing base for columns--Dimensions | EQV ISO 2934-73 |
| 25.060 | J58 | GB/T 3668.9-1983 | 组合机床通用部件 主轴部件尺寸 | Modular units for machine tool construction--Spindle units--Dimensions | EQV ISO 3590-76 |
| 25.060 | J58 | GB/T 3668.10-1983 | 组合机床通用部件 多轴箱主轴端部和可调接杆尺寸 | Modular units for machine tool construction--Spindle noses and adjustable adaptors for multi-spindle heads --Dimensions | EQV ISO 2905-74 |
| 25.060 | J58 | GB/T 3668.11-1983 | 组合机床通用部件 有导轨立柱尺寸 | Modular units for machine tool construction--Integral way columns--Dimensions | EQV ISO 3589-75 |
| 25.060 | J58 | GB/T 3668.12-1983 | 组合机床通用部件 落地式有导轨立柱尺寸 | Modular units for machine tool construction--Floor-mounted type--Integral way columns--Dimensions | EQV ISO 3970-77 |
| 25.060 | J58 | GB/T 3668.13-1983 | 组合机床通用部件 安装多轴箱用的法兰盘和端面传动键尺寸 | Modular units for machine tool construction--Tenon drive and flanges for mounting multi-spindle heads--Dimensions | EQV ISO 3476-75 |
| 25.160.20 | J33 | GB/T 3669-2001 | 铝及铝合金焊条 | Aluminum and aluminum-alloy electrodes for shielded metal arc welding | NEQ AWS A513/A5.3M:1999 |
| 25.160.20 | J33 | GB/T 3670-1995 | 铜及铜合金焊条 | Coated electrodes for copper and copper alloys | NEQ ANSI/AWS A5.6-84 |
| 25.160.20 | J33 | GB/T 3731-1983 | 涂料焊条效率、金属回收率和熔敷系数的测定 | Covered electrodes--Determination of the efficiency, metal recovery and deposition coefficient | EQV ISO 2401-72 |
| 25.140.20 | C68 | GB 3787-1993 | 手持式电动工具的管理、使用、检查和维修安全技术规程 | Technical safety code for management, operation, inspection maintenance of hand-held motor operated tools | |
| 25.100.25 | J14 | GB/T 3832.1-1983 | 拉刀矩形柄 型式和基本尺寸 | Rectangular shanks for broaches--Types and main dimensions | |
| 25.100.25 | J14 | GB/T 3832.2-1983 | 拉刀圆柱形前柄型式和基本尺寸 | Round shanks for broaches--Types and main dimensions | |
| 25.100.25 | J14 | GB/T 3832.3-1983 | 拉刀圆柱形后柄型式和基本尺寸 | Round follower end for broaches--Types and main dimensions | |
| 25.060.20 | J51 | GB/T 3837-2001 | 7:24手动换刀刀柄圆锥 | 7/24 tapers for tool shanks for manual changing | EQV ISO 297:1988 |
| 25.140.20 | K64 | GB 3883.1-2000 | 手持式电动工具的安全 第一部分: 通用要求 | Safety of hand-held motor-operated electric tools Part 1: General requirements | IDT IEC 60745-1:1997 |
| 25.140.20 | K64 | GB 3883.2-1991 | 手持式电动工具的安全 第二部分: 螺丝刀和冲击扳手的专用要求 (可供认证用) | Safety of hand-held motor-operated electric tools - Part 2: Particular requirements for screwdrivers and impact wrenches | IDT IEC 60745-2-2-82 |
| 25.140.20 | K64 | GB 3883.3-1991 | 手持式电动工具的安全 第二部分: 电动砂轮机、抛光机和盘式砂光机的专用要求 (可供认证用) | Safety of hand-held motor-operated electric tools - Part 2: Particular requiements for electric grinders, polishers and disk-type sanders | IDT IEC 60745-2-3-84 |
| 25.140.20 | K64 | GB 3883.4-1991 | 手持式电动工具的安全 第二部分: 砂光机的专用要求 (可供认证用) | Safety of hand-held motor-operated electric tools - Part 2: Particular requirements for sanders | IDT IEC 60745-2-4-83 |
| 25.140.20 | K64 | GB 3883.5-1998 | 手持式电动工具的安全 第二部分: 圆锯和圆刀的专用要求 | Safety of hand-held motor-operated tools Part 2: Particular requirments for circular saws and circular knives | IDT IEC 60745-2-5:1993 |
| 25.140.20 | K64 | GB 3883.6-1991 | 手持式电动工具的安全 第二部分: 电钻的专用要求 (可供认证用) | Safety of hand-held motor-operated electric tools - Part 2: Particular reqiements for electric drills | IDT IEC 60745-2-1 |
| 25.140.20 | K64 | GB 3883.7-1991 | 手持式电动工具的安全 第二部分: 电锤的专用要求 (可供认证用) | Safety of hand-held motor-operated electric tools - Part 2: Particular requirements for electric hammers | IDT IEC 60745-2-6 |
| 25.140.20 | K64 | GB 3883.8-1991 | 手持式电动工具的安全 第二部分: 电剪刀的专用要求 (可供认证用) | Safety of hand-held motor-operated electric tools - Part 2: Particular requirements for sheet matal shears | IDT IEC 60745-2-5-82 |
| 25.140.20 | K64 | GB 3883.9-1991 | 手持式电动工具的安全 第二部分: 电动攻丝机的专用要求 (可供认证用) | Safety of hand-held motor-operated electric tools - Part 2: Particular requirements for electric tappers | IDT IEC 60745-2-9-84 |
| 25.140.20 | K64 | GB 3883.10-1991 | 手持式电动工具的安全 第二部分: 电刨的专用要求 (可供认证用) | Safety of hand-held motor-operated electric tools - Part 2: Particlar requirements for electric planers | IDT IEC 60745-2-14-84 |
| 25.140.20 | K64 | GB 3883.11-1991 | 手持式电动工具的安全 第二部分: 电动往复锯 (曲线锯、刀锯) 的专用要求 (可供认证用) | Safety of hand-held motor-operated electric tools - Part 2: Particular requirements for electric reciprocating saws (jig and sabre saws) | IDT IEC 60745-2-11-84 |
| 25.140.20 | K64 | GB 3883.12-1991 | 手持式电动工具的安全 第二部分: 混凝土振动器 (插入式振动器) 的专用要求 (可供认证用) | Safety of hand-held motor-operated electric tools - Part 2: Particular requirements for concrete vibrators (internal vibrators) | IDT IEC 60745-2-12-82 |
| 25.140.20 | K64 | GB 3883.13-1992 | 手持式电动工具的安全 第二部分: 不易燃液体电喷枪的专用要求 | Safety of hand held motor operated electric tools--Part 2: Particular requirements for spray guns for non-flammable liquids | IDT IEC 60745-2-7 |
| 25.140.20 | K64 | GB 3883.14-1993 | 手持式电动工具的安全 第二部分: 电链锯的专用要求 | Safety of hand held motor operated electric tools--Part 2: Particular requirements for chain saws | IDT IEC 60745-3-13-89 |
| 25.140.20 | K64 | GB 3883.15-1993 | 手持式电动工具的安全 第二部分: 电动修枝剪与电动草剪的专用要求 | Safety of hand held motor operated electric tools--Part 2: Particular requirements for hedge trimmers and grass shears | IDT IEC 60745-2-15-84 |
| 25.140.20 | K64 | GB 3883.16-1993 | 手持式电动工具的安全 第二部分: 电动钉钉机的专用要求 | Safety of hand-held motor operated electric tools--Part 2: Particular requirements for tackers | IDT IEC 60745-2-16 |
| 25.140.20 | K64 | GB 3883.17-1993 | 手持式电动工具的安全 第二部分: 电动木铣与电动修边机的专用要求 | Safety of hand held motor operated electric tools--Part 2: Particular requirements for routers and immers | IDT IEC 60745-2-17-89 |
| 25.080.20 | J54 | GB/T 3932-1983 | 工作台不升降铣床精度 | Milling machines with table of fixed height with horizontal or vertical spindle--Testing of the accuracy | NEQ ISO 1984-82 |
| 25.080.20 | J54 | GB/T 3933-1983 | 升降台铣床精度 | Milling machines with table of variable height with horizontal or vertical spindle--Testing of the accuracy | NEQ ISO 1701-74 |
| 25.160.20 | J33 | GB/T 3965-1995 | 熔敷金属中扩散氢测定方法 | Methods for determination of diffusible hydrogen in deposited metal | NEQ JIS Z 3118-86 |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.080.40 | J54 | GB/T 4017-1997 | 摇臂钻床 精度检验 | Radial drilling machines--Testing of the accuracy | EQV ISO 2423:1982 |
| 25.080.40 | J54 | GB/T 4018.1-1997 | 圆柱立式钻床 精度检验 第1部分: 几何精度检验 | Pillar type vertical drilling machines--Testing of the accuracy--Part 1: Testing of the geometric accuracy | EQV ISO 2773-1:1973 |
| 25.080.40 | J54 | GB/T 4018.2-1997 | 圆柱立式钻床 精度检验 第2部分: 工作精度检验 | Pillar type vertical drilling machines--Testing of the accuracy--Part 2: Testing of the working accuracy | EQV ISO 2773-2:1973 |
| 25.080.40 | J54 | GB/T 4019.1-1997 | 方柱立式钻床 精度检验 第1部分: 几何精度检验 | Box type vertical drilling machines--Testing of the accuracy--Part 1: Geometrical tests | EQV ISO 2772-1:1973 |
| 25.080.40 | J54 | GB/T 4019.2-1997 | 方柱立式钻床 精度检验 第2部分: 工作精度检验 | Bot type vertical drilling machines--Testing of the accuracy--Part 2: Working tests | EQV ISO 2772-2:1974 |
| 25.080.10 | J53 | GB/T 4020-1997 | 卧式车床精度检验 | Acceptance conditions for general purpose parallel lathes--Testing of the accuracy | EQV ISO 1708:1989 |
| 25.080.50 | J55 | GB/T 4022-1983 | 卧轴矩台平面磨床 精度 | Surface grinding machines with horizontal grinding wheel spindle and reciprocating table--Testing of the accuracy | NEQ ISO 1986-74 |
| 25.100.70 | J43 | GB/T 4127-1997 | 普通磨具 形状和尺寸 | Shapes and dimensions for bonded abrasive products | |
| 25.120.30 | J46 | GB/T 4169.1-1984 | 塑料注射模具零件 推杆 | Components of injection mould for plastics--Ejector pins | EQV ISO 6751-82 |
| 25.120.30 | J46 | GB/T 4169.2-1984 | 塑料注射模具零件 直导套 | Components of injection mould for plastics--Straight guide bushes | |
| 25.120.30 | J46 | GB/T 4169.3-1984 | 塑料注射模具零件 带头导套 | Components of injection mould for plastics--Guide bushes with head | |
| 25.120.30 | J46 | GB/T 4169.4-1984 | 塑料注射模具零件 带头导柱 | Components of injection mould for plastics--Guide pillars with head | |
| 25.120.30 | J46 | GB/T 4169.5-1984 | 塑料注射模具零件 有肩导柱 | Components of injection mould for plastics -- Guide pillars with shoulder | |
| 25.120.30 | J46 | GB/T 4169.6-1984 | 塑料注射模具零件 垫块 | Components of injection mould for plastics -- Spacer blocks | |
| 25.120.30 | J46 | GB/T 4169.7-1984 | 塑料注射模具零件 推板 | Components of injection mould for plastics--Ejector plates | |
| 25.120.30 | J46 | GB/T 4169.8-1984 | 塑料注射模具零件 模板 | Components of injection mould for plastics--Mould plates | EQV ISO 6753-82 |
| 25.120.30 | J46 | GB/T 4169.9-1984 | 塑料注射模具零件 限位钉 | Components of injection mould for plastics--Stop pins | |
| 25.120.30 | J46 | GB/T 4169.10-1984 | 塑料注射模具零件 支承柱 | Components of injection mould for plastics--Support pillars | |
| 25.120.30 | J46 | GB/T 4169.11-1984 | 塑料注射模具零件 圆锥定位件 | Components of injection mould for plastics--Locating elements | |
| 25.120.30 | J46 | GB/T 4170-1984 | 塑料注射模具零件技术条件 | Components of injection mould for plastics--Specifica-tion | |
| 25.100.10 | J41 | GB/T 4211-1984 | 高速钢车刀条 | High speed steel tool bits | NEQ ISO 5421-77 |
| 25.100.30 | J41 | GB/T 4243-1984 | 锥柄长刃机用铰刀 | Long fluted machine reamers with Morse taper shanks | NEQ ISO 236/2-76 |
| 25.100.30 | J41 | GB/T 4244-1984 | 带刃倾角直柄机用铰刀 | Machine reamers with edge inclination with parallel shanks | |
| 25.100.30 | J41 | GB/T 4245-1984 | 机用铰刀技术条件 | Machine reamers--Technical requirements | |
| 25.100.30 | J41 | GB/T 4246-1984 | 铰刀专用公差 | Special tolerance for reamers | NEQ ISO 522-75 |
| 25.100.30 | J41 | GB/T 4247-1984 | 锥柄机用桥梁铰刀 | Machine bridge reamers with Morse taper shanks | NEQ ISO 2238-72 |
| 25.100.30 | J41 | GB/T 4248-1984 | 手用1:50锥度销子铰刀技术条件 | Hand taper 1:50 reamers--Technical requirements | |
| 25.100.30 | J41 | GB/T 4250-1984 | 圆锥铰刀技术条件 | Taper reamers--Technical requirements | |
| 25.100.30 | J41 | GB/T 4251-1984 | 硬质合金直柄机用铰刀 | Machine reamers with parallel shanks with carbide tips | |
| 25.100.30 | J41 | GB/T 4252-1984 | 硬质合金锥柄机用铰刀 | Machine reamers with Morse taper shanks with carbide tips | |
| 25.100.30 | J41 | GB/T 4253-1984 | 硬质合金铰刀技术条件 | Reamers with carbide tips--Technical requirements | |
| 25.100.30 | J41 | GB/T 4255-1984 | 套式铰刀和套式扩孔钻用心轴 | Arbors for shell reamers and shell core drills | NEQ ISO 2402-72 |
| 25.100.30 | J41 | GB/T 4256-1984 | 直柄扩孔钻 | Core drills with parallel shanks | NEQ ISO 7079-81 |
| 25.100.30 | J41 | GB/T 4257-1984 | 扩孔钻技术条件 | Core drills--Technical requirements | |
| 25.100.30 | J41 | GB/T 4258-1984 | 60°、90°、120°直柄锥面锪钻 | Countersinks with parallel shanks for angles 60°90°and 120°inclusive | NEQ ISO 3294-75 |
| 25.100.30 | J41 | GB/T 4259-1984 | 锥面锪钻技术条件 | Countersinks--technical requirements | |
| 25.100.30 | J41 | GB/T 4260-1984 | 带导柱直柄平底锪钻 | Counterbores with parallel shanks and solid pilots | NEQ ISO 4206-77 |
| 25.100.30 | J41 | GB/T 4261-1984 | 带可换导柱锥柄平底锪钻 | Counterbores with morse taper shanks and detachable pilots | NEQ ISO 4207-77 |
| 25.100.30 | J41 | GB/T 4262-1984 | 平底锪钻技术条件 | Counterbores--technical requirements | |
| 25.100.30 | J41 | GB/T 4263-1984 | 带导柱直柄90°锥面锪钻 | 90°Countersinks with parallel shanks and solid pilots | NEQ ISO 4205-77 |
| 25.100.30 | J41 | GB/T 4264-1984 | 带可换导柱锥柄90°锥面锪钻 | 90°Countersinks with morse taper shanks and detachable pilots | NEQ ISO 4204-77 |
| 25.100.30 | J41 | GB/T 4265-1984 | 90°锥面锪钻技术条件 | 90°Countersinks--technical requirements | |
| 25.100.30 | J41 | GB/T 4266-1984 | 锪钻用可换导柱 | Detachable pilots for use with counterbores and countersinks | NEQ ISO 4208-77 |
| 25.100.30 | J41 | GB/T 4267-1984 | 直柄回转工具用柄部直径和传动方头尺寸 | Rotating tools with parallel shanks--Diameters of shanks and sizes of driving squares | NEQ ISO 237-75 |
| 25.060.20 | J52 | GB/T 4346-1984 | 三爪自定心卡盘 基本参数和尺寸 | 3-jaw self-centering chucks--Dimensions | |
| 25.140 | J47 | GB/T 4388-1995 | 呆扳手、梅花扳手、两用扳手的型式 | Types of open-end wrenches, box wrenches and combination wrenches | NEQ ISO 10102-1990 |
| 25.140 | J47 | GB/T 4389-1995 | 螺钉与螺母的装配工具 双头呆扳手、双头梅花扳手、两用扳手头部外形的最大尺寸 | Assembly tool for screws and nuts-Openend double-head engineers wrenches, doublehead box wrenches and combination wrenches-Maximum outside dimensions of heads | IDT ISO 3318-1990 |
| 25.140 | J47 | GB/T 4390-1995 | 公制扳手开口和扳手孔的常用公差 | Spanner gaps and sockets-Metric series-tolerances for general use | EQV ISO 691-1983 |
| 25.140 | J47 | GB/T 4391-1995 | 双头扳手的对边尺寸组配 | Combinations of double-end wrenche gaps | NEQ ISO 1085-1986 |
| 25.140 | J47 | GB/T 4392-1995 | 敲击呆扳手和敲击梅花扳手 | Slugging open-end wrenches and slugging box wrenches | |
| 25.140 | J47 | GB/T 4393-1995 | 呆扳手 - 梅花扳手、两用扳手 技术规范 | Open-end wrenches, box wrenches and combination wrenches-Technical specifications | NEQ ISO 1711-1975 |
| 25.040.40 | N10 | GB/T 4439-1984 | 工业自动化仪表工作条件 振动 | Industrial process measurement and control instrument operating conditions--Vibration | |
| 25.140.30 | J47 | GB/T 4440-1998 | 活扳手 | Adjustable wrenches | NEQ ISO/CD 6787:1996 |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.140.20 | K64 | GB/T 4583-1995 | 电动工具噪声测量方法 工程法 | Measurement of noise emitted by electric tools-Engineering method | NEQ ISO 3700-80 |
| 25.140 | J47 | GB/T 4625-1998 | 螺钉和螺母的装配工具术语 | Assembly tools for screws and nuts-nomenclature | IDT ISO 1703:1983 |
| 25.160.40 | J33 | GB/T 4675.1-1984 | 焊接性试验 斜Y型坡口焊接裂纹试验方法 | Weldability testing--Method of Y-groove cracking test | EQV JIS Z3158-66 |
| 25.160.40 | J33 | GB/T 4675.2-1984 | 焊接性试验 搭接接头(CTS) 焊接裂纹试验方法 | Weldability testing--Method of controlled thermal severity cracking test | EQV JIS Z3154-62 |
| 25.160.40 | J33 | GB/T 4675.3-1984 | 焊接性试验 T型接头焊接裂纹试验方法 | Weldability testing--Method of cracking test for welded tee joint | EQV JIS Z3153-71 |
| 25.160.40 | J33 | GB/T 4675.4-1984 | 焊接性试验 压板对接(FISCO) 焊接裂纹试验方法 | Weldability testing--Method of FISCO cracking test | EQV JIS Z3155-79 |
| 25.160.40 | J33 | GB/T 4675.5-1984 | 焊接性试验 焊接热影响区最高硬度试验方法 | Weldability testing--Testing method of maximum hard ness in weld heat-affected zone | EQV JIS Z3101-76 |
| 25.100.70 | J43 | GB/T 4676-1984 | 普通磨料取样方法 | Method for sampling of conventional abrasive grains | NEQ JIS R6003-73 |
| 25.120.30 | J46 | GB/T 4678.1-1984 | 压铸模零件 模块 | Die-cast die components--Mold plates | EQV ISO 6753-82 |
| 25.120.30 | J46 | GB/T 4678.2-1984 | 压铸模零件 圆形镶块 | Die-cast die components--Round insert blocks | |
| 25.120.30 | J46 | GB/T 4678.3-1984 | 压铸模零件 矩形镶块 | Die-cast die components--Rectangular insert blocks | |
| 25.120.30 | J46 | GB/T 4678.4-1984 | 压铸模零件 A型导柱 | Die-cast die components--Guide pins type A | |
| 25.120.30 | J46 | GB/T 4678.5-1984 | 压铸模零件 B型导柱 | Die-cast die components--Guide pins type B | |
| 25.120.30 | J46 | GB/T 4678.6-1984 | 压铸模零件 A型导套 | Die-cast die components--Guide bushings type A | |
| 25.120.30 | J46 | GB/T 4678.7-1984 | 压铸模零件 B型导套 | Die-cast die components--Guide bushings type B | |
| 25.120.30 | J46 | GB/T 4678.8-1984 | 压铸模零件 推板 | Die-cast die components--Ejector plates | |
| 25.120.30 | J46 | GB/T 4678.9-1984 | 压铸模零件 推板导柱 | Die-cast die components--Guide pins for ejector plate | |
| 25.120.30 | J46 | GB/T 4678.10-1984 | 压铸模零件 推板导套 | Die-cast die components--Guide bushings for ejector plate | |
| 25.120.30 | J46 | GB/T 4678.11-1984 | 压铸模零件 推杆 | Die-cast die components--Ejector pins | |
| 25.120.30 | J46 | GB/T 4678.12-1984 | 压铸模零件 复位杆 | Die-cast die components--Return pins | |
| 25.120.30 | J46 | GB/T 4678.13-1984 | 压铸模零件 推板垫圈 | Die-cast die components--Ejector plate washers | |
| 25.120.30 | J46 | GB/T 4678.14-1984 | 压铸模零件 限位钉 | Die-cast die components--Stop pins | |
| 25.120.30 | J46 | GB/T 4678.15-1984 | 压铸模零件 垫块 | Die-cast die components--Spacer blocks | |
| 25.120.30 | J46 | GB/T 4679-1984 | 压铸模零件技术条件 | Specification of the die-cast die components | |
| 25.100.25 | J57 | GB/T 4680-1997 | 卧式内拉床 精度检验 | Horizontal internal broaching machines--Testing of the accuracy | EQV ISO 6480:1983 |
| 25.080.50 | J55 | GB/T 4681-1984 | 无心磨床 精度 | External cylindrical centerless grinding machines--Testing of the accuracy | NEQ ISO 3875-80 |
| 25.080.50 | J55 | GB/T 4682-1984 | 内圆磨床 精度 | Internal cylindrical grinding machines with horizontal spindles--Testing of the accuracy | NEQ ISO 2407-73 |
| 25.080.10 | J53 | GB/T 4683-1993 | 转塔车床精度 | Turret lathes--Testing of the accuracy | |
| 25.080.50 | J55 | GB/T 4684-1994 | 外圆磨床 参数 | External cylindrical grinding machines--Parameters | NEQ DIN 55005 B1.6 |
| 25.080.50 | J55 | GB/T 4685-1994 | 外圆磨床 精度 | External cylindrical grinding machines--Accuracy | NEQ ISO 2433-84 |
| 25.080 | J57 | GB/T 4686-1984 | 插齿机精度 | Gear shaping machines--Testing of the accuracy | |
| 25.040.40 | L09 | GB 4793.1-1995 | 测量、控制和试验室用电气设备的安全要求 第1部分: 通用要求 | Safety requirements for electrical equipment for measurement, control, and laboratory use Part 1: General requirements | IDT IEC 61010-1-90 |
| 25.040.40 | N10 | GB/T 4830-1984 | 工业自动化仪表气源压力范围和质量 | Pressure range and quality of air supply for the industrial process measurement and control instruments | |
| 25.220.20 | A29 | GB/T 4955-1997 | 金属覆盖层 覆盖层厚度测量 阳极溶解库仑法 | Metallic coatings--Measurement of coating thickness--Coulometric method by anodic dissolution | IDT ISO 2177:1985 |
| 25.220.40 | A29 | GB/T 4956-1985 | 磁性金属基体上非磁性覆盖层厚度测量 磁性方法 | Non-magnetic coatings on magnetic substrates--Measurement of coating thickness--Magnetic method | EQV ISO 2178-82 |
| 25.220.40 | A29 | GB/T 4957-1985 | 非磁性金属基体上非导电覆盖层厚度测量 涡流方法 | Non-conductive coatings on non-magnetic metal substrates--Measurement of coating thickness--Eddy current method | EQV ISO 2360-82 |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.120.20 | J62 | GB 5091-1985 | 压力机的安全装置技术要求 | Technical requirememts for safety devices of the presses | |
| 25.120.20 | J62 | GB 5092-1985 | 压力机用感应式安全装置技术条件 | Technical requirements for induction type safety device used for the presses | |
| 25.? | J62 | GB 5093-1985 | 压力机用手持电磁吸盘技术条件 | Technical requirements for hand-held electromagnetic disk used for the presses | |
| 25.100.25 | J41 | GB/T 5102-1985 | 渐开线花键拉刀技术条件 | Broaches for involute spline technical specifications | |
| 25.100.25 | J41 | GB/T 5103-1985 | 渐开线花键滚刀通用技术条件 | The general technical specifications for involute splines hobs | NEQ ISO 4468-82 |
| 25.100.25 | J41 | GB/T 5104-1985 | 30°压力角渐开线花键滚刀基本型式和尺寸 | The basic types and dimensions of hobs for 30°pressure angle involute splines | NEQ ISO 2490-75 |
| 25.100.25 | J41 | GB/T 5105-1985 | 45°压力角渐开线花键滚刀基本型式和尺寸 | The basic types and dimensions of hobs for 45°pressure angle involute splines | |
| 25.160.30 | J64 | GB/T 5107-1985 | 焊接和切割用软管接头 | Hose connection for equipment for welding and cutting | NEQ ISO 3253-75(E) |
| 25.160.20 | J33 | GB/T 5117-1995 | 碳钢焊条 | Carbon steel covered electrodes | EQV ANSI/AWS A5.1-91 |
| 25.160.20 | J33 | GB/T 5118-1995 | 低合金钢焊条 | Low alloy steel covered electrodes | NEQ ANSI/SWS A5.5-81 |
| 25.160.10 | J33 | GB/T 5185-1985 | 金属焊接及钎焊方法在图样上的表示代号 | Welding, brazing, braze welding and soldering of metals--List of processes for symbolic representation on drawings | EQV ISO 4063-78 |
| 25.220.40 | J13 | GB/T 5267-1985 | 螺纹紧固件电镀层 | Electroplated coatings on threaded fasteners | |
| 25.060.20 | J53 | GB/T 5268-1985 | 车床刀架装刀槽高度 | Machine tools--Lathe tool posts--Overall internal height | NEQ ISO 213-82 |
| 25.220.40 | A29 | GB/T 5270-1985 | 金属基体上的金属覆盖层 (电沉积层和化学沉积层) 附着强度试验方法 | Metallic coatings on metallic substrates--Electrodepo-sited and chemically deposited coatings--Review of methods available for testing adhesion | EQV ISO 2819-80 |
| 25.080.50 | J55 | GB/T 5288-1985 | 龙门导轨磨床精度 | Slideways grinding machines with two columns--Testing of the accuracy | NEQ ISO 4703-77 |
| 25.080.20 | J54 | GB/T 5289.2-2000 | 卧式铣镗床检验条件 精度检验 第2部分: 台式机床 | Test conditions for boring and milling machines with horizontal spindle--Testing of the accuracy Part 2: Table--type machines | NEQ ISO 3070-2:1997 |
| 25.120.40 | J59 | GB/T 5290.1-2001 | 电火花成形机 参数 第1部分: 单立柱机床(十字工作台型和固定工作台型) | Die sinking electro-discharge machines(EDM)--Parameters Part 1: Single column machines(cross slide table type and fixed table type) | |
| 25.120.40 | J59 | GB/T 5291.1-2001 | 电火花成形机 精度检验 第1部分: 单立柱机床(十字工作台型和固定工作台型) | Die sinking electro-discharge machines(EDM)--Testing of accuracy Part 1: Single column machines (cross slide table type and fixed table type) | EQV ISO 11090-1:1998 |
| 25.160.20 | J33 | GB/T 5293-1999 | 埋弧焊用碳钢焊丝和焊剂 | Carbon steel electrodes and fluxs for submerged arc welding | EQV ANSI/AWS A5.17:1989 |
| 25.140 | J47 | GB/T 5305-1985 | 手工具包装、标志、运输与贮存 | Packaging,marking,transportation and storage of hand tools | |
| 25.160.20 | H71 | GB/T 5315-1985 | Ni-B-Si系自熔合金粉 | Metallic powder material--Self-fluxing Ni-B-Si alloy powder | |
| 25.160.20 | H71 | GB/T 5316-1985 | Ni-Cr-B-Si系自熔合金粉 | Metallic powder material--Self-fluxing Ni-Cr-B-Si alloy powder | NEQ JIS H8303-76 |
| 25.100.20 | J41 | GB/T 5340-1985 | 可转位立铣刀 | Endmilling cutters with indexable inserts | NEQ ISO 6262/2-82 |
| 25.100.20 | J41 | GB/T 5341-1985 | 可转位三面刃铣刀 | Side and facemilling cutters with indexable inserts | NEQ ISO 6986-83 |
| 25.100.20 | J41 | GB/T 5342-1985 | 可转位面铣刀 | Facemilling cutters with indexable inserts | NEQ ISO 6462-83 |
| 25.060.20; | J41 | GB/T 5343.1-1993 | 可转位车刀及刀夹型号表示规则 | Turning toolholders and cartridges for indexable inserts--Designation | EQV ISO 5608-89 |
| 25.100.10 | J41 | GB/T 5343.2-1993 | 可转位车刀型式尺寸和技术条件 | Turning tools with indexable inserts--Types,dimensions and technical specifications | NEQ ISO 5610-89 |
| 25.140 | J47 | GB/T 5356-1998 | 内六角扳手 | Hexagon socket screw keys | NEQ ISO 2936:1995 |
| 25.140 | J47 | GB/T 5357-1998 | 内六角花形扳手 | Hexagon spline wrenches | |
| 25.140 | J47 | GB/T 5358-1998 | 内六角花形螺钉旋具 | Hexagon spline screwdrivers | |
| 25.140.20 | K64 | GB/T 5580-2001 | 电钻 | Electric drills | |
| 25.020 | J31 | GB/T 5611-1998 | 铸造术语 | Foundry terminology | |
| 25.220 | A29 | GB/T 5619-1985 | 防锈材料百叶箱试验方法 | Shed storage exposure test--Testing method for rust-proof material | |
| 25.140.10 | J84 | GB/T 5621-1999 | 凿岩机械与气动工具 性能试验方法 | Test methods of performance for rock drilling machines and pneumatic tools | EQV ISO 2787:1984 |
| 25.040.40 | N26 | GB/T 5691-1985 | 数据处理用的模块化仪器系统 CAMAC 系统 | A modular instrumentation system for data handling--CAMAC system | IDT IEC 60516-75 |
| 25.040.40 | N26 | GB/T 5692-1985 | CAMAC 术语的定义 | Definitions of CAMAC terms | IDT IEC 60678-80 |
| 25.040.40 | N26 | GB/T 5693-1985 | CAMAC 多机箱系统结构分支信息公路和A1型CAMAC 机箱控制器规范 | CAMAC organization of multi-crate systems specification of the branch-highway and CAMAC crate controller type A1 | IDT IEC 60552-77 |
| 25.040.40 | N26 | GB/T 5694-1985 | CAMAC 系统中的块传送 | Block transfers in CAMAC systems | IDT IEC 60677-80 |
| 25.100.70 | J43 | GB/T 5766-1996 | 摩擦材料洛氏硬度试验方法 | Test method of Rockwell hardness for friction materials | NEQ JIS D 4421-1987 |
| 25.140 | J47 | GB/T 5806-1986 | 锉刀通用技术条件 | General technical condition of files | |
| 25.140 | J47 | GB/T 5807-1986 | 锉刀试验方法 | Test methods of files | |
| 25.140 | J47 | GB/T 5808-1986 | 锉刀检验规则、标志与包装 | Test regulations, marking and packaging of files | |
| 25.140 | J47 | GB/T 5809-1986 | 锉刀分类、编号规则 | Classification and numbering regulations of files | |
| 25.060.10 | J50 | GB/T 5900.1-1997 | 机床 主轴端部与花盘 互换性尺寸 第1部分: A型 | Machine tools--Spindle noses and face plates--Sizes for interchangeability--Part 1: Type A | EQV ISO 702/I:1975 |
| 25.060.10 | J50 | GB/T 5900.2-1997 | 机床 主轴端部与花盘 互换性尺寸 第2部分: 凸轮锁紧型 | Machine tools--Spindle noses and face plates--Sizes for interchangeability--Part 2: Camlock type | EQV ISO 702/Ⅱ:1975 |
| 25.060.10 | J50 | GB/T 5900.3-1997 | 机床 主轴端部与花盘 互换性尺寸 第3部分: 卡口型 | Machine tools--Spindle noses and face plates--Sizes for interchangeability--Part 3: Bayonet type | EQV ISO 703/Ⅲ:1975 |
| 25.060.20 | J52 | GB/T 5901.1-1986 | 四爪单动卡盘 型式、基本参数和尺寸 | Types, basic parameters and dimensions of four-jaw independent chucks | |
| 25.060.20 | J52 | GB/T 5901.2-1986 | 四爪单动卡盘 精度 | Testing of accuracy of four-jaw independent chucks | |
| 25.060.20 | J52 | GB/T 5901.3-1986 | 四爪单动卡盘 技术条件 | Technical specifications of four-jaw independent chucks | |
| 25.120.20 | E34 | GB 5903-1995 | 工业闭式齿轮油 | Gear oils for industrial enclosed gear drives | |
| 25.180.10 | K61 | GB 5959.1-1986 | 电热设备的安全 第一部分 通用要求 | Safety in electroheat installations--Part 1: General requirements | NEQ IEC 60519-1-84 |
| 25.180.10 | K61 | GB 5959.2-1998 | 电热设备的安全 第二部分 对电弧炉设备的特殊要求 | Safety in electroheat installations-part 2 Particular requirements for arc furnace installations | IDT IEC 60519-4:1995 |
| 25.180.10 | K61 | GB 5959.3-1988 | 电热设备的安全 第三部分 对感应和导电加热设备以及感应熔炼设备的特殊要求 | Safety in electroheat installations--Part 3: Particular requirements for induction and conduction heating installations and induction melting installations | EQV IEC 60519-3-85 |
| 25.180.10 | K60 | GB 5959.4-1992 | 电热设备的安全 第四部分: 对电阻炉的通用要求 | Safety in electroheat installations--Part 4: General requirements for resistance furnaces | EQV IEC 60519-2-75 |
| 25.180.10 | K60 | GB 5959.5-1991 | 电热设备的安全 第五部分 等离子设备的安全规程 | Safety in electroheat installations - Part 5: Specifications for safety in plasma installations | EQV IEC 60519-5-80 |
| 25.180.10 | K61 | GB 5959.6-1987 | 电热设备的安全 第六部分 对工业微波加热设备的特殊要求 | Safety in electroheat installations--Part 6: Particular requirements for industrial microwave heating installations | EQV IEC 60519-6-82 |
| 25.180.10 | K61 | GB 5959.7-1987 | 电热设备的安全 第七部分 对具有电子枪的电热设备的特殊要求 | Safety in electroheat installations--part 7: Particular requirements for installations with electron guns | EQV IEC 60519-7-83 |
| 25.180.10 | K61 | GB 5959.8-1989 | 电热设备的安全 第八部分 对电渣重熔炉的特殊要求 | Safety in electroheat installations--part 8: Particular requirements for electro-slag remelting furnaces | EQV IEC 60519-8-83 |
| 25.180.10 | K61 | GB 5959.9-1989 | 电热设备的安全 第九部分 对高频介质加热设备的特殊要求 | Safety in electroheat installations？Part 9: Particular requirements for high-frequency dielectric heating installations | EQV IEC 60519-9-87 |
| 25.180.10 | K60 | GB 5959.11-2000 | 电热设备的安全 第11部分: 对液态金属电磁搅拌、输送或浇注设备的特殊要求 | Safety in electroheat installations-Part 11: Particular requirements for installations for electromagnetic stirring,transport or pouring of metal liquids | IDT IEC 60519-11:1997 |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.020 | J31 | GB/T 6060.1-1997 | 表面粗糙度比较样块 铸造表面 | Roughness comparison specimens--Cast surfaces | EQV ISO 2632/Ⅲ:1979 |
| 25.120.10 | J62 | GB 6077-1985 | 剪切机械安全规程 | Safety regulations for shearing machinery | |
| 25.100.30 | J41 | GB/T 6078.1-1998 | 中心钻 第1部分: 不带护锥的中心钻-A型 型式和尺寸 | Centre drills Part 1: Centre drills for centre holes without protecting chamfers-Type A Dimensions | EQV ISO 866-1975 |
| 25.100.30 | J41 | GB/T 6078.2-1998 | 中心钻 第2部分: 带护锥的中心钻-B型 型式和尺寸 | Centre drills Part 2: Centre drills for centre holes with protecting chamfers--Type B Dimensions | IDT ISO 2540-1973 |
| 25.100.30 | J41 | GB/T 6078.3-1998 | 中心钻 第3部分: 弧形中心钻-R型 型式和尺寸 | Centre drills Part 3: Centre drills for centre holes with radius form--Type R Dimensions | IDT ISO 2541-1972 |
| 25.100.30 | J41 | GB/T 6078.4-1998 | 中心钻 第4部分: 技术条件 | Center drills Part 4: Technical specifications | |
| 25.100.40 | J41 | GB/T 6080.1-1998 | 机用锯条 第1部分: 型式与尺寸 | Machine hacksaw blades Part 1: Dimensions | IDT ISO 2336.2:1996 |
| 25.100.40 | J41 | GB/T 6080.2-1998 | 机用锯条 第2部分: 技术条件 | Machine hacksaw blades Part 2: Technical specifications | |
| 25.100.20 | J41 | GB/T 6081-2001 | 直齿插齿刀 基本型式和尺寸 | The basic types and dimensions for spur shaper cutters | |
| 25.100.20 | J41 | GB/T 6082-2001 | 直齿插齿刀 通用技术条件 | The general technical specifications for spur shaper cutters | |
| 25.100.20 | J41 | GB/T 6083-2001 | 齿轮滚刀 基本型式和尺寸 | The basic type and dimensions of gear hobs | EQV ISO 2490:1996 |
| 25.100.20 | J41 | GB/T 6084-2001 | 齿轮滚刀 通用技术条件 | The general technical specifications for gear hobs | EQV ISO 4468:1982 |
| 25.060.20 | J52 | GB/T 6087-1993 | 扳手钻夹头 | Key type drill chuck | |
| 25.060.20 | J52 | GB/T 6090-1993 | 钻夹头圆锥 | Drill chuck tapers | |
| 25.120.20 | H72 | GB/T 6110-1985 | 硬质合金拉制模具 型式和尺寸 | Hardmetal dies for drawing wires and bars--Types and dimensions | EQV ISO 1684-75 |
| 25.100.20 | J41 | GB/T 6117.1-1996 | 立铣刀 第1部分: 直柄立铣刀的型式和尺寸 | End mills--Part 1: Milling cutters with parallel shanks | EQV ISO 1641-1-1987 |
| 25.100.20 | J41 | GB/T 6117.2-1996 | 立铣刀 第2部分: 莫氏锥柄立铣刀的型式和尺寸 | End mills--Part 2: Milling cutters with morse taper shanks | EQV ISO 1641-2-1978 |
| 25.100.20 | J41 | GB/T 6117.3-1996 | 立铣刀 第3部分: 7/24锥柄立铣刀的型式和尺寸 | End mills--Part 3: Milling cutters with 7/24 taper shanks | EQV ISO 1641-3-1978 |
| 25.100.20 | J41 | GB/T 6118-1996 | 立铣刀 技术条件 | End mills--Technical specifications | |
| 25.100.20 | J41 | GB/T 6119.1-1996 | 三面刃铣刀 型式和尺寸 | Side and face milling cutter--Tapes and dimensions | EQV ISO 2587-1972 |
| 25.100.20 | J41 | GB/T 6119.2-1996 | 三面刃铣刀 技术条件 | Side and face milling cutter--Technical specifications | |
| 25.100.20 | J41 | GB/T 6120-1996 | 锯片铣刀 型式和尺寸 | Metal slitting saws--Types and dimensions | EQV ISO 2296-1972 |
| 25.100.20 | J41 | GB/T 6121-1996 | 锯片铣刀 技术条件 | Metal slitting saws--Technical specifications | |
| 25.100.20 | J41 | GB/T 6122-1985 | 圆角铣刀 | Corner-rounding cutters | NEQ ISO 3860-76 |
| 25.100.20 | J41 | GB/T 6124.1-1996 | T型槽铣刀 第1部分: 直柄T型槽铣刀的型式和尺寸 | T-slot cutters--Part 1: Dimensions of T-slot cutters with plain or flated parallel shanks | EQV ISO 3337-1978 |
| 25.100.20 | J41 | GB/T 6124.2-1996 | T型槽铣刀 第2部分: 莫氏锥柄T型槽铣刀的型式和尺寸 | T-slot cutters--Part 2: Dimensions of T-slot cutters with Morse taper shanks with tapped holes | EQV ISO 3337-1978 |
| 25.100.20 | J41 | GB/T 6125-1996 | T型槽铣刀 技术条件 | T-slot cutters--Technical specifications | |
| 25.100.20 | J41 | GB/T 6128.1-1996 | 角度铣刀 第1部分: 单角铣刀的型式和尺寸 | Angle milling cutter--Part 1: The types and dimensions for single angle cutters | |
| 25.100.20 | J41 | GB/T 6128.2-1996 | 角度铣刀 第2部分: 不对称双角铣刀的型式和尺寸 | Angle milling cutter--Part 2: The types and dimensions for double unequal-angle cutters | |
| 25.100.20 | J41 | GB/T 6128.3-1996 | 角度铣刀 第3部分: 对称双角铣刀的型式和尺寸 | Angle milling cutter--Part 3: The types and dimensions for double equal-angle cutters | EQV ISO 6108-1978 |
| 25.100.20 | J41 | GB/T 6129-1996 | 角度铣刀 技术条件 | Angle cutters--Technical specifications | |
| 25.100.40 | J41 | GB/T 6130-2001 | 镶片圆锯 | Segmental circular metal cutting saws | EQV ISO 2924:1973 |
| 25.100.20 | J41 | GB/T 6131.1-1996 | 铣刀直柄 第1部分: 普通直柄的型式和尺寸 | Parallel shanks for milling cutters--Part 1: Dimensional characteristics of plain parallel shanks | EQV ISO 3338/1-1993 |
| 25.100.20 | J41 | GB/T 6131.2-1996 | 铣刀直柄 第2部分: 削平直柄的型式和尺寸 | Parallel shanks for milling cutters--Part 2: Dimensional characteristics of flatted parallel shanks | EQV ISO 3338-2-1985 |
| 25.100.20 | J41 | GB/T 6131.3-1996 | 铣刀直柄 第3部分: 2°斜削平直柄的型式和尺寸 | Parallel shanks for milling cutters--Part 3: Dimensional characteristics of parallel shanks with 2°angular flats | EQV ISO/CD 3338-3-1993 |
| 25.100.20 | J41 | GB/T 6131.4-1996 | 铣刀直柄 第4部分: 螺纹柄的型式和尺寸 | Parallel shanks for milling cutters--Part 4: Dimensional characteristics of screwed shanks | EQV ISO/DIS 3338-4-1993 |
| 25.? | J41 | GB/T 6132-1993 | 铣刀和铣刀刀杆的互换尺寸 | Interchang eability dimensions for milling cutters and arbors | |
| 25.060.20 | J41 | GB/T 6133-1985 | 削平型直柄刀具夹头 | Tool chucks for flated parallel shank tools | EQV ISO 5414/1~2-82 |
| 25.100.30 | J41 | GB/T 6135.1-1996 | 直柄麻花钻 第1部分: 粗直柄小麻花钻的型式和尺寸 | Parallel shank twist drills--Part 1: The types and dimensions for small type twist drills with oversize parallel shank | |
| 25.100.30 | J41 | GB/T 6135.2-1996 | 直柄麻花钻 第2部分: 直柄短麻花钻的型式和尺寸 | Parallel shank twist drills--Part 2: The types and dimensions for parallel shank stub series twist drills | EQV ISO 235-1980 |
| 25.100.30 | J41 | GB/T 6135.3-1996 | 直柄麻花钻 第3部分: 直柄麻花钻的型式和尺寸 | Parallel shank twist drills--Part 3: The types and dimesnions for parallel shank jobber series twist drills | EQV ISO 235-1980 |
| 25.100.30 | J41 | GB/T 6135.4-1996 | 直柄麻花钻 第4部分: 直柄长麻花钻的型式和尺寸 | Parallel shank twist drills--Part 4: The types and dimensions for parallel shank long series twist drills | EQV ISO 494-1975 |
| 25.100.30 | J41 | GB/T 6135.5-1996 | 直柄麻花钻 第5部分: 直柄超长麻花钻的型式和尺寸 | Parallel shank twist drills--Part 5: The types and dimensions for extra long parallel shank twist drills | EQV ISO/DIS 3292 |
| 25.100.30 | J41 | GB/T 6138.1-1997 | 攻丝前钻孔用阶梯麻花钻 第1部分: 直柄阶梯麻花钻的型式和尺寸 | Subland twist drills for holes prior to tapping screw threads Part 1: The types and dimensions for subland twist drills with parallel shanks | EQV ISO 3439:1975 |
| 25.100.30 | J41 | GB/T 6138.2-1997 | 攻丝前钻孔用阶梯麻花钻 第2部分: 莫氏锥柄阶梯麻花钻的型式和尺寸 | Subland twist drills for holes prior to tapping screw threads Part 2: The types and dimensions for subland twist drills with Morse shanks | EQV ISO 3438:1975 |
| 25.100.30 | J41 | GB/T 6139-1997 | 阶梯麻花钻 技术条件 | Subland twist drills--Technical specifications | NEQ ISO/DIS 10899 |
| 25.160.20 | J33 | GB/T 6208-1995 | 钎料型号表示方法 | Filler metal for soft soldering and brazing--Designation | NEQ ISO 3677-1992 |
| 25.140.10 | J84 | GB/T 6247-1986 | 凿岩机械与气动工具名词术语 | Terminology of rock drilling machines and pneumatic tools | NEQ ISO 3857/1~3-77 |
| 25.140.30 | J47 | GB/T 6289-1999 | 夹扭钳和剪切钳 术语 | Pliers and nippers--Nomenclature | IDT ISO 5742:1982 |
| 25.140.30 | J47 | GB/T 6290-1999 | 夹扭钳和剪切钳 通用技术条件 | Pliers and nippers--General technical requirements | NEQ ISO 5743:1988 |
| 25.140.30 | J47 | GB/T 6291-1999 | 夹扭钳和剪切钳 试验方法 | Pliers and nippers--Methods of test | EQV ISO 5744:1988 |
| 25.060.20 | J42 | GB/T 6320-1997 | 杠杆齿轮比较仪 | Mechanical dial comparators | NEQ DIN 879-1983 |
| 25.100.20 | J41 | GB/T 6338-1986 | 直柄燕尾槽铣刀和直柄反燕尾槽铣刀 | Dovetail and inverse dovetail milling cutters with plain parallel shanks | NEQ ISO 3859-85 |
| 25.100.20 | J41 | GB/T 6339-1986 | 削平型直柄燕尾槽铣刀和削平型直柄反燕尾槽铣刀 | Dovetail and inverse dovetail milling cutters with flatted parallel shanks | NEQ ISO 3859-85 |
| 25.100.20 | J41 | GB/T 6340-1986 | 直柄燕尾槽铣刀和直柄反燕尾槽铣刀技术条件 | Dovetail and inrerse dovetail milling cutters with parallel shanks technical specificatians | |
| 25.010 | J05 | GB/T 6403.1-1986 | 球面半径 | Radii of sphere surfaces | |
| 25.010 | J05 | GB/T 6403.2-1986 | 润滑槽 | Lubricating grooves | |
| 25.010 | J05 | GB/T 6403.3-1986 | 滚花 | Knurl | |
| 25.010 | J05 | GB/T 6403.4-1986 | 零件倒圆与倒角 | Rounding and chamferd of parts | |
| 25.010 | J05 | GB/T 6403.5-1986 | 砂轮越程槽 | Relief grooves for grinding wheels | |
| 25.100.70 | J43 | GB/T 6405-1994 | 人造金刚石和立方氮化硼 品种 | Types of synthetic diamond and cubic boron nitride | |
| 25.100.70 | J43 | GB/T 6406-1996 | 超硬磨料 金刚石或立方氮化硼颗粒尺寸 | Super abrasive--Grain sizes of diamond or cubic boron nitride | EQV ISO 6106-1979 |
| 25.100.70 | J43 | GB/T 6408-1986 | 立方氮化硼技术条件 | Technical requirements for cubic boron nitride | |
| 25.100.70 | J43 | GB/T 6409.1-1994 | 超硬磨具和锯 形状总览、标记 | Superhard abrasive products and saws---General survey designation | NEQ ISO 6104-79 |
| 25.100.70 | J43 | GB/T 6409.2-1996 | 超硬磨料制品 金刚石或立方氮化硼磨具 形状和尺寸 | Abrasive products--Diamond or cubic boron nitride grinding tools--Form and dimensions | EQV ISO 6168-1980 |
| 25.100.70 | J43 | GB/T 6409.3-1986 | 金钢石或立方氮化硼磨具 带柄油石 | Diamond or cubic boron nitride--Hand sticks | |
| 25.100.70 | J43 | GB/T 6409.4-1986 | 金刚石或立方氮化硼磨具 标志和包装 | Marking and packing for diamond or cubic boron nitride abrasive products | |
| 25.160.40 | J33 | GB/T 6416-1986 | 影响钢熔化焊接头质量的技术因素 | Technical factors influencing the quality of the fusion welded joints in steel | EQV ISO 3088-75 |
| 25.160.40 | J33 | GB/T 6417-1986 | 金属熔化焊焊缝缺陷分类及说明 | Classification of imperfections in metallic fusion welds, with explanations | EQV ISO 6520-82 |
| 25.160.50? | J33 | GB/T 6418-1993 | 铜基钎料 | Copper base brazing filler metals | NEQ JIS Z 3262 |
| 25.220.40 | A29 | GB/T 6461-1986 | 金属覆盖层 对底材为阴级的覆盖层 腐蚀试验后的电镀试样的评级 | Metallic coatings--Coatings cathodic to the substrate--Rating of electro-plated test specimens subjected to corrosion tests | EQV ISO 4540-80 |
| 25.220.40 | A29 | GB/T 6462-1986 | 金属和氧化物覆盖层 横断面厚度显微镜测量方法 | Metallic and oxide coatings--Measurement of coating thickness--Microscopical method | EQV ISO 1463-82 |
| 25.220.40 | A29 | GB/T 6463-1986 | 金属和其他无机覆盖层 厚度测量方法评述 | Metallic and other non-organic coatings--Review of methods of measurement of thickness | EQV ISO 3882-86 |
| 25.220.10 | A29 | GB/T 6464-1997 | 金属及其覆盖层 大气腐蚀试验 现场试验的一般要求 | Metals and its coatings--Atmospheric corrosion testing--General requirements for field tests | EQV ISO 8565:1992 |
| 25.220.40 | A29 | GB/T 6465-1986 | 金属和其他无机覆盖层 腐蚀膏腐蚀试验 (CORR试验) | Metallic and other non-organic coatings--Corrodkote corrosion test(CORR test) | EQV ISO 4541-78 |
| 25.220.40 | A29 | GB/T 6466-1986 | 电沉积铬层 电解腐蚀试验(EC试验) | Electrodeposited chromium coatings--Electrolytic corrosion testing (EC test) | EQV ISO 4539-80 |
| 25.080.50 | J55 | GB/T 6469-1986 | 卧轴矩台平面磨床 参数 | Surface grinding machines with horizontal spindle and rectangular table--Parameters | |
| 25.080.50 | J55 | GB/T 6470-1986 | 无心外圆磨床参数 | External cylindrical centerless grinding machines--Parameters | |
| 25.080.50 | J55 | GB/T 6471-1986 | 内圆磨床参数 | Internal cylindrical grinding machines--Parameters | |
| 25.080.30 | J57 | GB/T 6472-1996 | 立式内拉床 精度检验 | Vertical internal broaching machines--Testing of the accuracy | EQV ISO 6779-1981 |
| 25.080.30 | J57 | GB/T 6473-1996 | 立式外拉床 精度检验 | Vertical surface broaching machines--Testing of the accuracy | EQV ISO 6481-1981 |
| 25.080.50 | J55 | GB/T 6474-1986 | 导轨磨床参数 | Surface grinding machines for grinding slideways--Parameters | |
| 25.080.50 | J55 | GB/T 6476-1986 | 立轴矩台平面磨床精度 | Surface grinding machines with vertical grinding wheel spindle and reciprocating table--Testing of the accuracy | NEQ ISO 1985-74 |
| 25.080 | J50 | GB/T 6477.1-1986 | 金属切削机床术语 基本术语 | Terminology for metal-cutting machine tools--Basic terminology | |
| 25.080 | J50 | GB/T 6477.2-1986【廃止】 | 金属切削机床术语 组合机床及组合机床自动线(2000年5月废止) | Terminology for metal-cutting machine tools--Modular machine tools and transfer lines | |
| 25.080 | J50 | GB/T 6477.3-1986 | 金属切削机床术语 车床 | Terminology for metal-cutting machine tools--Lathes | |
| 25.080 | J50 | GB/T 6477.4-1986 | 金属切削机床术语 钻床 | Terminology for metal-cutting machine tools--Drilling machines | |
| 25.080 | J50 | GB/T 6477.5-1986 | 金属切削机床术语 镗床 | Terminology for metal-cutting machine tools--Boring machines | |
| 25.080 | J50 | GB/T 6477.6-1986 | 金属切削机床术语 磨床 | Terminology for metal-cutting machine tools--Grinding machines | |
| 25.080 | J50 | GB/T 6477.7-1986 | 金属切削机床术语 齿轮加工机床 | Terminology for metal-cutting machine tools--Gear cutting machines | |
| 25.080 | J50 | GB/T 6477.8-1986 | 金属切削机床术语 螺纹加工机床 | Terminology for metal-cutting machine tools--Threading machines | |
| 25.080 | J50 | GB/T 6477.9-1986 | 金属切削机床术语 铣床 | Terminology for metal-cutting machine tools--Milling machines | |
| 25.080 | J50 | GB/T 6477.10-1986 | 金属切削机床术语 刨床和插床 | Terminology for metal-cutting machine tools--Planing and slotting machines | |
| 25.080 | J50 | GB/T 6477.11-1986 | 金属切削机床术语 拉床 | Terminology for metal-cutting machine tools--Broaching machines | |
| 25.080 | J50 | GB/T 6477.13-1986 | 金属切削机床术语 锯床 | Terminology for metal-cutting machine tools--Sawing machines | |
| 25.080 | J50 | GB/T 6477.14-1986 | 金属切削机床术语 刻线机 | Terminology for metal-cutting machine tools--Dividing machines | |
| 25.080 | J50 | GB/T 6477.15-1986 | 金属切削机床术语 管子加工机床 | Terminology for metal-cutting machine tools--Pipe cutting machines | |
| 25.080 | J50 | GB/T 6477.16-1986 | 金属切削机床术语 机床附件 | Terminology for metal-cutting machine tools--Machine tool accessory | |
| 25.180.10 | K61 | GB/T 6542-1986 | 直接电弧炉的试验方法 | Test methods for direct arc furnaces | EQV IEC 60676-80 |
| 25.220.10 | A29 | GB/T 6807-2001 | 钢铁工件涂装前磷化处理技术条件 | Specifications for phosphating treatment of iron and steel parts before painting | |
| 25.220.40 | A29 | GB/T 6808-1986 | 铝及铝合金阳极氧化着色阳极氧化膜耐晒度的人造光加速试验 | Anodizing of aluminium and its alloys--Accelerated test of light fastness of coloured anodic oxide coatings using artificial light | EQV ISO 2135-84 |
| 25.100.70 | J43 | GB/T 6966.1-1986 | 人造金刚石微粉和立方氮化硼微粉 品种 | Types of synthetic diamond micropowder and cubic boron nitride micropowder | |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.160.40 | J33 | GB/T 7032-1986 | T型角焊接头弯曲试验方法 | Method of bend test for T type fillet welded joint | |
| 25.120.30 | J31 | GB/T 7143-1986 | 铸造用硅砂化学分析方法 | Methods for chemical analysis of silica sand for foundry | |
| 25.160.30 | K64 | GB/T 7157-1987 | 电烙铁 | Electric soldering irons | |
| 25.080.50 | J55 | GB/T 7177-1987 | 双端面磨床参数 | Double disc surface grinding machines？Parameters | |
| 25.200 | J36 | GB/T 7232-1999 | 金属热处理工艺术语 | Terminology of metal heat treatment | NEQ DIN EN10052:1994
JIS B6905:1995 |
| 25.180 | K61 | GB/T 7405-1987 | 埋弧炉试验方法 | Test methods for submerged-arc furnaces | EQV IEC 60683-80 |
| 25.180 | K61 | GB/T 7406-1987 | 具有电子枪的电热设备试验方法 | Test methods for electroheating installations with electron guns | EQV IEC 60703-81 |
| 25.220.50 | Y20 | GB/T 7410-1987 | 搪瓷名词术语 | Terms of vitreous and porcelain enamels | |
| 25.140.20 | K64 | GB/T 7442-2001 | 角向磨光机 | Electric angle grinders | |
| 25.140.20 | K64 | GB/T 7443-2001 | 电锤 | Electric rotary hammers | |
| 25.040.40 | F80 | GB/T 7521-1987 | 多个控制器在-CAMAC机箱中 | Multiple controllers in a CAMAC crate | EQV IEC 60729-82 |
| 25.040.40 | F80 | GB/T 7522-1987 | CAMAC串行信息公路接口系统 | CAMAC-Serial highway interface systems | EQV IEC 60640-79 |
| 25.040.40 | F80 | GB/T 7523-1987 | CAMAC子程序 | Subroutines for CAMAC | EQV IEC 60713-82 |
| 25.080.50 | J55 | GB/T 7923-1987 | 立轴矩台平面磨床 参数 | Surface grinding machines with vertical grinding wheel spindle and reciprocating table--Parameters | |
| 25.080.50 | J55 | GB/T 7924-1987 | 光学曲线磨床 参数 | Optical projection profile grinding machines--Parameters | |
| 25.120.10 | J59 | GB/T 7925-1987 | 电火花线切割机参数 | Parameters of wire cut electric discharge machines | NEQ JIS B6360-83 |
| 25.120.10 | J59 | GB/T 7926-1987 | 电火花线切割机精度 | Accuracy of wire cut electric discharge machines | NEQ ΓOCT 19589-80 |
| 25.220.50 | G90 | GB/T 7987-1987 | 搪玻璃层耐温差急变性试验方法 | Test methods for thermal shock resistance of glass-lined layer | NEQ ISO 2747-73 |
| 25.220.50 | G90 | GB/T 7988-1987 | 搪玻璃釉耐热氢氧化钠溶液腐蚀性能的测定 | Determination of resistance to hot sodium hydroxide of vitreous enamel | NEQ ISO 2734-83 |
| 25.220.50 | G90 | GB/T 7989-1987 | 搪玻璃釉耐沸腾盐酸腐蚀性能的测定 | Determination of resistance to boiling hydrochloric acid of vitreous enamel | NEQ ISO 2733-83 |
| 25.220.50 | G90 | GB/T 7990-1987 | 搪玻璃层耐机械冲击试验方法 | Impact test method of glass-lined layer | NEQ ISO 2064-80 |
| 25.220.50 | G90 | GB/T 7991-1987 | 搪玻璃层的厚度测量 电磁法 | Method for measuring the thicknees of glass-lined layer by electromagnetic meter | NEQ ISO 2723-73 |
| 25.220.50 | G90 | GB/T 7993-1987 | 用在腐蚀条件下的搪玻璃设备的高电压试验方法 | Test method of glass-lined equipment for service under corrosive conditions by high voltage | NEQ ISO 2746-73 |
| 25.220.50 | G90 | GB/T 7994-1987 | 搪玻璃设备水压试验方法 | Hydraulic pressure test of glass-lined equipments | |
| 25.220.50 | G90 | GB/T 7995-1987 | 搪玻璃设备气密性试验方法 | Air seal test method of glass-lined equipments | |
| 25.220.50 | G90 | GB/T 7996-1987 | 搪玻璃容器公称容积与公称直径 | Nominal volume and nominal diameter for glass-lined vessel | NEQ JIS R4201-83 |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.160.50 | J33 | GB/T 8012-2000 | 铸造锡铅焊料 | Casting tin-lead solders | |
| 25.220.40 | H61 | GB/T 8013-1987 | 铝及铝合金阳极氧化 阳极氧化膜的总规范 | Anodizing of aluminium and aluminium alloys--General specifications for anodic oxidation coatings | IDT ISO 7599-83 |
| 25.220.40 | H61 | GB/T 8014-1987 | 铝及铝合金阳极氧化 阳极氧化膜厚度的定义和有关测量厚度的规定 | Anodizing of aluminium and aluminium alloys--Definitions thickness of anodic oxidation coatings and conventions concerning the measurement of thickness | IDT ISO 2164-80 |
| 25.220.40 | H25 | GB/T 8015.1-1987 | 铝及铝合金阳极氧化膜厚度的试验方法 重量法 | Test methods for thickness of anodic oxidation coatings on aluminium and aluminium alloys--Gravimetric method | IDT ISO 2106-82 |
| 25.220.40 | H25 | GB/T 8015.2-1987 | 铝及铝合金阳极氧化膜厚度的试验方法 分光束显微法 | Test methods for thickness of anodic oxidation coatin-gs on aluminium and aluminium alloys--Split-beam mic-roscope method | IDT ISO 2128-76 |
| 25.080 | J56 | GB/T 8064-1998 | 滚齿机 精度检验 | Acceptance conditions for gear hobbing machines--Testing of the accuracy | EQV ISO 6545:1992(E) |
| 25.160.20 | J33 | GB/T 8110-1995 | 气体保护电弧焊用碳钢、低合金钢焊丝 | Welding wires for gas shielding arc welding of carbon and low alloy steels | NEQ ANSI/AWS A5.18-79 |
| 25.160.30 | J64 | GB/T 8118-1995 | 电弧焊机通用技术条件 | The general specification for arc welding machines | NEQ IEC 60974/1-1989 |
| 25.200 | J36 | GB/T 8121-1987 | 热处理工艺材料名词术语 | The terminology of technological materials for heat treatment | |
| 25.040.20 | J07 | GB/T 8129-1997 | 工业自动化系统 机床数值控制 词汇 | Industrial automation systems--Numerical control of machines--Vocabulary | IDT ISO 2806:1994 |
| 25.220 | H68 | GB/T 8184-1987 | 铑电镀液 | The rhodium eletroplating solution | |
| 25.160.30 | J64 | GB/T 8366-1996 | 电阻焊设备的额定值与运行条件 | Rating of resistance welding equipment | EQV ISO 669-1981 |
| 25.140 | J47 | GB/T 8389.2-1987 | 斧的通用技术条件 | Axes--General technical requirements | |
| 25.160.20 | J33 | GB/T 8454-1987 | 焊条用还原钛铁矿粉中亚铁量的测定 | Determination of ferrous iron content in reduced ilmenite powder for welding rod | |
| 25.120.01 | J32 | GB/T 8541-1997 | 锻压术语 | Terminolgy of forging and stamping | |
| 25.160.40 | J33 | GB/T 8619-1988 | 钎缝强度试验方法 | Method of the strength test for brazed and soldered seam | |
| 25.180 | K65 | GB/T 8623-1988 | 金属管状远红外辐射加热器 | Metal tube far infraed heater | |
| 25.220.40 | H26 | GB/T 8752-1988 | 铝及铝合金阳极氧化 薄阳极氧化膜连续性的检验 硫酸铜试验 | Anodizing of aluminium and aluminium alloys--Check of continuity of thin anodic oxide coatings--Copper sulphate test | IDT ISO 2085-86 |
| 25.220.40 | H26 | GB/T 8753-1988 | 铝及铝合金阳极氧化 阳极氧化膜封闭后吸附能力的损失评定 酸处理后的染色斑点试验 | Anodizing of aluminium and aluminium alloys--Estimation of loss of absorptive power of anodic oxide coatings after sealing--Dye spot test with prior acid treatment | IDT ISO 2143-81 |
| 25.220.40 | H21 | GB/T 8754-1988 | 铝及铝合金阳极氧化 应用击穿电位测定法检验绝缘性 | Anodizing of aluminium and aluminium alloys--Insulation check by measurement of breakdown potential | IDT ISO 2376-72 |
| 25.120.30 | J46 | GB/T 8844-1988 | 压铸模技术条件 | Specification of the die-casting dies | |
| 25.120.30 | J46 | GB/T 8845-1988 | 冲模术语 | Terminology for dies | |
| 25.120.30 | J46 | GB/T 8846-1988 | 塑料成型模具术语 | Terminology of mould for plastics | |
| 25.120.30 | J46 | GB/T 8847-1988 | 压力铸造模具术语 | Terminology for die-casting die | |
| 25.040.20 | J50 | GB/T 8870-1988 | 机床数字控制 点位、直线运动和轮廓控制系统的数据格式 | Numerical control of machines--Data format for positioning ,line motion and contouring control systems | EQV ISO 6983/1-82 |
| 25.220.20 | A29 | GB/T 8923-1988 | 涂装前钢材表面锈蚀等级和除锈等级 | Rust grades and preparation grades of steel surfaces before application of paints and related products | EQV ISO 8501/1-88 |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.080 | J56 | GB/T 9059-1988 | 精密插齿机精度 | Precision gear shaping machines？Testing of the accuracy | NEQ ISO 5466-80 |
| 25.080 | J50 | GB/T 9061-1988 | 金属切削机床通用技术条件 | General specifications for metal-cutting machine tools | |
| 25.100.20 | J41 | GB/T 9062-1988 | 硬质合金错齿三面刃铣刀 | Side and face milling cutters with double alternate helical teeth with carbide tips | NEQ ISO 5466-80 |
| 25.140.10 | K04 | GB/T 9088-1988 | 电动工具型号编制方法 | Types organization method for electric tools | |
| 25.120.10 | J62 | GB/T 9165-1988 | 开式压力机 精度 | Open front mechanical power presses？Testing of the accuracy | EQV ISO 6899-84 |
| 25.120.10 | J62 | GB/T 9166-1988 | 四柱液压机 精度 | Four-column hydraulic presses - Testing of the accuracy | NEQ JIS B6403-77 |
| 25.080.20 | J56 | GB/T 9167-1988 | 花键轴铣床 精度 | Splint hobbing machines - Testing of the accuracy | NEQ ΓOCT 5642-77 |
| 25.060.20 | J52 | GB/T 9204.1-1988 | 固定顶尖 参数 | Dead centre - Parameter | NEQ ISO 298-73 |
| 25.060.20 | J52 | GB/T 9204.2-1988 | 固定顶尖 精度 | Dead centre - Testing of the accuracy | |
| 25.060.20 | J52 | GB/T 9204.3-1988 | 固定顶尖 技术条件 | Dead centre - Specification | |
| 25.100.30 | J41 | GB/T 9205-1988 | 镶片齿轮滚刀 | Insterted blaeds gear hobs | |
| 25.100.60 | J41 | GB/T 9206-1988 | 硬质合金圆柱形旋转锉 | Cylindrical hardmetal burrs | NEQ ISO 7755/2-84 |
| 25.100.60 | J41 | GB/T 9207-1988 | 硬质合金圆柱形球头旋转锉 | Cylindrical round-(ball-) nose hardmetal burrs | NEQ ISO 7755/3-84 |
| 25.100.60 | J41 | GB/T 9208-1988 | 硬质合金圆球形旋转锉 | Spherical hardmetal hurrs | NEQ ISO 7755/4-84 |
| 25.100.60 | J41 | GB/T 9209-1988 | 硬质合金椭圆形旋转锉 | Oval hardmetal burrs | NEQ ISO 7755/5-84 |
| 25.100.60 | J41 | GB/T 9210-1988 | 硬质合金弧形圆头旋转锉 | Arch round-(ball-) nose hardmetal burrs | NEQ ISO 7755/6-84 |
| 25.100.60 | J41 | GB/T 9211-1988 | 硬质合金弧形尖头旋转锉 | Arch pointed-nose hardmetal burrs | NEQ ISO 7755/7-84 |
| 25.100.60 | J41 | GB/T 9212-1988 | 硬质合金火炬形旋转锉 | Flame hardmetal burrs | NEQ ISO 7755/8-84 |
| 25.100.60 | J41 | GB/T 9213-1988 | 硬质合金60°和90°圆锥形旋转锉 | 60°and 90°cone hardmetal burrs | NEQ ISO 7755/9-84 |
| 25.100.60 | J41 | GB/T 9214-1988 | 硬质合金锥形圆头旋转锉 | Conical round-(ball-) nose hardmetal burrs | NEQ ISO 7755/10-84 |
| 25.100.60 | J41 | GB/T 9215-1988 | 硬质合金锥形尖头旋转锉 | Conical pointed-nose hardmetal burrs | NEQ ISO 7755/11-84 |
| 25.100.60 | J41 | GB/T 9216-1988 | 硬质合金倒锥形旋转锉 | Inverted cone hardmetal burrs | NEQ ISO 7755/12-84 |
| 25.100.60 | J41 | GB/T 9217-1988 | 硬质合金旋转锉技术条件 | Hardmetal burrs technical specifications | NEQ ISO 7755/1-84 |
| 25.040.40 | N18 | GB/T 9249-1988 | 工业过程测量和控制系统用自动平衡式记录仪和指示仪 | Self-balance recorders and indicators for use in industrial-process measurement and control systems | NEQ JIS C1802-81 |
| 25.100.70 | J43 | GB/T 9258.1-2000 | 涂附磨具用磨料 粒度分析 第1部分: 粒度组成 | Coated abrasives--Grain size analysis--Part 1: Grain size distribution test | IDT ISO 6344-1:1998 |
| 25.100.70 | J43 | GB/T 9258.2-2000 | 涂附磨具用磨料 粒度分析 第2部分: 粗磨粒P12？P220粒度组成的测定 | Coated abrasives--Grain size analysis--Part 2: Determination of grain size distribution of macrogrits P12 to P220 | IDT ISO 6344-2:1998 |
| 25.100 | J43 | GB/T 9258.3-2000 | 涂附磨具用磨料 粒度分析 第3部分: 微粉P240 - P2500粒度组成的测定 | Coated abrasives--Grain size analysis--Part 3: Determination of grain size distribution of microgrits P240 to P2500 | IDT ISO 6344-3:1998 |
| 25.040.40 | L74 | GB/T 9362-1988 | 用于工业过程控制 实时FORTRAN | Industrial real-time FORTRAN--Application for the control of industrial processes | EQV ISO 7846-85 |
| 25.220.20 | L64 | GB/T 9415.2-1988 | 信息处理 数据存储设备用磁盘盘片 外径 200mm、内径63.5mm、每道96000 次磁道翻转 | Information processing--Magnetic disk for data storage devices-96000 flux transitions per track,200mm outer diameter, 63.5mm inner diameter | IDT ISO 7297-85 |
| 25.220.20 | L64 | GB/T 9415.3-1988 | 信息处理 数据存储设备用磁盘盘片 外径 210mm、内径 100mm、每道158000次磁道翻转 | Information processing--Magnetic disk for data storage devices-158000 flux transitions per track, 210mm outer diameter, 100mm inner diameter | |
| 25.220.20 | L64 | GB/T 9416.1-1988 | 信息处理 数据交换用130mm 改进调频制记录的位密度为7958磁道翻转/ 弧度、道密度为1.9道/毫米的双面软磁盘 第一部分 尺寸、物理性能和磁性能 | Information processing--Data interchange on 130mm flexible disk cartridges using modified frequency modulation recording at 7958 ftprad, 1.9tpmm, on both sides--Part 1: Dimensional, physical and magnetic characteristics | IDT ISO 7487/1-85 |
| 25.220.20 | L64 | GB/T 9416.2-1988 | 信息处理 数据交换用 130mm改进调频制记录的位密度为7958磁道翻转/ 弧度、道密度为1.9道/毫米的双面软磁盘 第二部分 磁道格式A | Information processing--Data interchange on 130mm flexible disk cartridges using modified frequency modulation recording at 7958 ftprad, 1.9tpmm, on both sides--Part 2: Track format A | IDT ISO 7487/2-85 |
| 25.220.20 | L64 | GB/T 9416.3-1988 | 信息处理 数据交换用 130mm改进调频制记录的位密度为7958磁道翻转 /弧度、道密度为1.9道/毫米的双面软磁盘 第三部分 磁道格式B | Information processing--Data interchange on 130mm flexible disk cartridges using modified frequency modulation recording at 7958 ftprad, 1.9tpmm, on both sides--Part 3: Track format B | IDT ISO 7487/3-85 |
| 25.020 | J31 | GB/T 9442-1998 | 铸造用硅砂 | Foundry silica sand | |
| 25.160.40 | J33 | GB/T 9446-1988 | 焊接用插销冷裂纹试验方法 | Welding--Cold cracking test method using implants | |
| 25.160.40 | J33 | GB/T 9447-1988 | 焊接接头疲劳裂纹扩展速率试验方法 | Test method for fatigue crack growth rates of welded joints | |
| 25.160.01 | J33 | GB 9448-1999 | 焊接与切割安全 | Safety in welding and cutting | EQV ANSI/AWS Z49.1 |
| 25.200 | J36 | GB/T 9450-1988 | 钢件渗碳淬火有效硬化层深度的测定和校核 | Determination and verification of the effective depth of carburizod and hardened cases of steel parts | EQV ISO 2639-82 |
| 25.200 | J36 | GB/T 9451-1988 | 钢件薄表面总硬化层深度或有效硬化层深度的测定 | Determination of total or effective thickness of thin surface hardened layers of steel parts | EQV ISO 4970-79 |
| 25.200 | J36 | GB/T 9452-1988 | 热处理炉有效加热区测定方法 | Testing method for working zone of heat treating furnace | |
| 25.120.30 | J46 | GB/T 9453-1988 | 锻模及其零件术语 | Terminology of forging dies and elements | |
| 25.160.20 | J33 | GB/T 9460-1988 | 铜及铜合金焊丝 | Welding wire and rods of copper and copper alloys | NEQ JIS Z3202-83 |
| 25.080.40 | J54 | GB/T 9461-1988 | 摇臂钻床参数 | Radial drilling machines--Parameters | |
| 25.040.40 | N17 | GB/T 9469.1-1988 | 分散型过程控制系统用工业过程数据公路 总论 | Process data highway, type C (PROWAY C), for distributed process control systems--Overview | EQV IEC 60955-86 |
| 25.040.40 | N17 | GB/T 9469.2-1988 | 分散型过程控制系统用工业过程数据公路 功能要求 | Process data highway, type C (PROWAY C), for distributed process control systems--Functional requirements | EQV IEC 60955-86 |
| 25.040.40 | N17 | GB/T 9469.3-1988 | 分散型过程控制系统用工业过程数据公路 与工业过程数据公路的接口 | Process data highway, type C (PROWAY C), for distributed process control systems--The interface to PROWAY | EQV IEC 60955-86 |
| 25.040.40 | N17 | GB/T 9469.4-1988 | 分散型过程控制系统用工业过程数据公路 工业过程数据公路链路控制 (PLC) 子层 | Process data highway, type C (PROWAY C), for distributed process control systems--The PROWAY link control (PLC)sublayer | EQV IEC 60955-86 |
| 25.040.40 | N17 | GB/T 9469.5-1988 | 分散型过程控制系统用工业过程数据公路 PLC-MAC 接口和服务规范 | Process data highway, type C (PROWAY C), for distributed process control systems--PLC-MAC interface and service specification | EQV IEC 60955-86 |
| 25.040.40 | N17 | GB/T 9469.6-1988 | 分散型过程控制系统用工业过程数据公路 媒体送取控制 (MAC)子层 | Process data highway, type C (PROWAY C), for distributed process control systems--The medium access control (MAC) sublayer | EQV IEC 60955-86 |
| 25.040.40 | N17 | GB/T 9469.7-1988 | 分散型过程控制系统用工业过程数据公路 MAC-物理层接口和规范 | Process data highway, type C (PROWAY C), for distributed process control systems--MAC-Physical layer interface specification | EQV IEC 60955-86 |
| 25.040.40 | N17 | GB/T 9469.8-1988 | 分散型过程控制系统用工业过程数据公路 单信道相位连续 FSK物理 (PHY)层及其与媒体接口的规范 | Process data highway, type C (PROWAY C), for distributed process control systems--Specification of the single channel phase-continuous-FKS physical (PHY) layer and its interface to the medium | EQV IEC 60955-86 |
| 25.040.40 | N17 | GB/T 9469.9-1988 | 分散型过程控制系统用工业过程数据公路 单信道同轴电缆总线媒体“层”技术规范 | Process data highway, type C (PROWAY C), for distributed process control systems--Single-channel coaxial-cable bus medium"layer"specification | EQV IEC 60955-86 |
| 25.040.40 | N17 | GB/T 9469.10-1988 | 分散型过程控制系统用工业过程数据公路 工业过程数据公路管理 | Process data highway, type C (PROWAY C), for distributed process control systems--PROWAY management | EQV IEC 60955-86 |
| 25.220.40 | A29 | GB/T 9789-1988 | 金属和其他非有机覆盖层 通常凝露条件下的二氧化硫腐蚀试验 | Metallic and other non-organic coatings--Sulfur dioxide test with general condensation of moisture | EQV ISO 6988-85 |
| 25.220.40 | A29 | GB/T 9790-1988 | 金属覆盖层及其他有关覆盖层 维氏和努氏显微硬度试验 | Metallic and related coatings--Vickers and Knoop microhardness tests | NEQ ISO 4516-80 |
| 25.220.40 | A29 | GB/T 9791-1988 | 锌和镉上铬酸盐转化膜试验方法 | Chromate conversion coatings on zinc and cadmium--Test methods | NEQ ISO 3613-80 |
| 25.220.40 | A29 | GB/T 9792-1988 | 金属材料上的转化膜 单位面积上膜层质量的测定 重量法 | Conversion coatings on metallic materials--Determination of coating mass per unit area--Gravimetric methods | EQV ISO 3892-80 |
| 25.220.40 | A29 | GB/T 9793-1997 | 金属和其他无机覆盖层 热喷涂 锌、铝及其合金 | Metallic and other inorganic coatings--Thermal spraying--Zinc、aluminium and their alloys | EQV ISO 2063:1991 |
| 25.220.40 | A29 | GB/T 9797-1997 | 金属覆盖层 镍+铬和铜+镍+铬电沉积层 | Metallic coatings--Electrodeposited coatings of nickel plus chromium and of copper plus nickel plus chromium | EQV ISO 1456:1988 |
| 25.220.40 | A29 | GB/T 9798-1997 | 金属覆盖层 镍电沉积层 | Metallic coatings--Electrodeposited coatings of nickel | EQV ISO 1458?:1988 |
| 25.220.40 | A29 | GB/T 9799-1997 | 金属覆盖层 钢铁上的锌电镀层 | Metallic coatings--Electroplated coatings of zinc on iron or steel | EQV ISO 2081:1986 |
| 25.220.40 | A29 | GB/T 9800-1988 | 电镀锌和电镀镉层的铬酸盐转化膜 | Chromate conversion coatings on electroplated zinc and cadmium coatings | EQV ISO 4520-81 |
| 25.220.50 | Y26 | GB/T 9988-1988 | 搪瓷耐碱性能测试方法 | Test method for alkali resistance of porcelain enamels | NEQ ASTM C614-80 |
| 25.220.50 | Y26 | GB/T 9989-1988 | 搪瓷耐室温柠檬酸性能测试方法 | Vitreous and porcelain enamels--Determination of resistance to citric acid at room temperature | IDT ISO 2722-73 |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.160.20 | J33 | GB/T 10044-1988 | 铸铁焊条及焊丝 | Covered electrodes and welding rods for welding cast iron | NEQ ANSI A5.15-82 |
| 25.160.20 | J33 | GB/T 10045-2001 | 碳钢药芯焊丝 | Carbon steel flux cored electrodes for arc welding | EQV ANSI/AWS A5.20:1995 |
| 25.160.50 | J33 | GB/T 10046-2000 | 银钎料 | Silver filler metals for brazing | EQV JIS Z 3261:1985 |
| 25.180.10 | K61 | GB/T 10066.4-1988 | 电热设备的试验方法 间接电阻炉 | Test methods for electroheat installations - Indirect resistance furnaces | |
| 25.180.10 | K61 | GB/T 10067.1-1988 | 电热设备基本技术条件 通用部分 | Basic specifications for electroheat installations--General | |
| 25.180.10 | K61 | GB/T 10067.2-1988 | 电热设备基本技术条件 炼钢电弧炉 | Basic specifications for electroheat installations--Steelmaking arc furnaces | |
| 25.180.10 | K61 | GB/T 10067.3-1988 | 电热设备基本技术条件 感应电热设备 | Basic specifications for electroheat installations--Induction electroheat installations | |
| 25.180.10 | K61 | GB/T 10067.4-1988 | 电热设备基本技术条件 间接电阻炉 | Basic specifications for electroheat installations--Indirect resistance furnaces | |
| 25.180.10 | K61 | GB/T 10067.5-1993 | 电热设备基本技术条件 高频介质加热设备 | Basic specifications for electroheat installations--high frequency dielectric heating installations | NEQ COCT 21139 |
| 25.220.40 | A29 | GB/T 10125-1997 | 人造气氛腐蚀试验 盐雾试验 | Corrosion tests in artificial atmospheres--Salt spray tests | EQV ISO 9227:1990 |
| 25.060 | J56 | GB/T 10173-1988 | 滚齿机 参数 | Gear hobbing machines--Parameters | |
| 25.160.30 | J64 | GB 10235-2000 | 弧焊变压器防触电装置 | Arc welding transformer hazard reducing device | |
| 25.160.30 | J64 | GB/T 10249-1988 | 电焊机型号编制方法 | The organization of model for electric welding machinees | |
| 25.160.20 | H13 | GB/T 10574.1-1989 | 锡铅焊料化学分析方法 碘酸钾滴定法测定锡量 | Tin-lead solders - Determination of tin content - Potassium iodate titrimetric method | |
| 25.160.20 | H13 | GB/T 10574.2-1989 | 锡铅焊料化学分析方法 孔雀绿分光光度法测定锑量 | Tin-lead solders - Determination of antimony content - Malachite green spectrophotometric method | |
| 25.160.20 | H13 | GB/T 10574.3-1989 | 锡铅焊料化学分析方法 溴酸钾滴定法测定锑量 | Tin-lead solders - Determination of antimony content - Potassium bromate titrimetric method | |
| 25.160.20 | H13 | GB/T 10574.4-1989 | 锡铅焊料化学分析方法 硫脲分光光度法测定铋量 | Tin-lead solders - Determination of bismuth content - Thiourea spectrophotometric method | |
| 25.160.20 | H13 | GB/T 10574.5-1989 | 锡铅焊料化学分析方法 1,10 -二氮杂菲分光光度法测定铁量 | Tin-lead solders - Determination of iron content - 1,10-phenanthroline spectrophotometric method | |
| 25.160.20 | H13 | GB/T 10574.6-1989 | 锡铅焊料化学分析方法 砷锑钼蓝分光光度法测定砷量 | Tin-lead solders - Determination of arsenic content - Molybdoantimony-arsenate blue spectrophotometric method | |
| 25.160.20 | H13 | GB/T 10574.7-1989 | 锡铅焊料化学分析方法 2,9-二甲基-1,10-二氮杂菲分光光度法测定铜量 | Tin-lead solders - Determination of copper content - 2,9-dimethyl-1,10-phenanthroline spectrophotometric method | |
| 25.160.20 | H13 | GB/T 10574.8-1989 | 锡铅焊料化学分析方法 火焰原子吸收光谱法测定银量 | Tin-lead solders - Detemination of silver content - Flame atomic absorption spectrophotometric method | |
| 25.160.20 | H13 | GB/T 10574.9-1989 | 锡铅焊料化学分析方法 电位滴定法测定银量 | Tin-lead solders - Determination of silver content - Potentiometric titrimetric method | |
| 25.160.20 | H13 | GB/T 10574.10-1989 | 锡铅焊料化学分析方法 火焰原子吸收光谱法测定锌量 | Tin-lead solders - Determination of zinc content - Flame atomic absorption spectrophotometric method | |
| 25.160.20 | H13 | GB/T 10574.11-1989 | 锡铅焊料化学分析方法 铬天青S-聚乙二醇辛基苯基醚分光光度法测定铝量 | Tin-lead solders - Determination of aluminum content - Chrome azurol S-polyethylene glycol oetyl phenyl ether spectrophotometric method | |
| 25.160.20 | H13 | GB/T 10574.12-1989 | 锡铅焊料化学分析方法 催化示波极谱法测定镉量 | Tin-lead solders - Determination of cadmium content - Catalytic oscillopolarographic method | |
| 25.160.20 | H13 | GB/T 10574.13-1989 | 锡铅焊料化学分析方法 磷钒钼杂多酸 -结晶紫分光光度法测定磷量 | Tin-lead solders - Determination of phosphorus content - Phosphor-vanadium-molybdium poly acid-crystal violet spectrophotometric method | |
| 25.160.20 | H13 | GB/T 10574.14-1989 | 锡铅焊料化学分析方法 蒸馏示波极谱法测定硫量 | Tin-lead solders？Determination of sulphur content - Oscillopolarographic method after distillation | |
| 25.140 | J47 | GB/T 10635-1989 | 螺钉旋具通用技术条件 | Screwdrivers - General technical requirements | |
| 25.140 | J47 | GB/T 10636-1989 | 螺钉旋具试验方法 | Screwdrivers - Test methods | |
| 25.140 | J47 | GB/T 10686-1989 | 铜合金工具防爆性能试验方法 | Testing method of copper alloy tools for explosive atmospheres | NEQ JIS M7002-84 |
| 25.160.20 | J33 | GB/T 10858-1989 | 铝及铝合金焊丝 | Aluminium and aluminium alloy welding rods and wires | NEQ JIS Z3232-86 |
| 25.160.20 | J33 | GB/T 10859-1989 | 镍基钎料 | Nickel base brazing filler metals | NEQ JIS Z3265-86 |
| 25.120.10 | J62 | GB/T 10923-1989 | 锻压机械 精度检验通则 | Acceptance code of accuracy for metalforming machine | NEQ ISO 230/1-86 |
| 25.120.20 | J62 | GB/T 10924-1989 | 闭式单点压力机 精度 | Straight sided one-point mechanical presses - Testing of the accuracy | NEQ JIS B6402-85 |
| 25.080.50 | J55 | GB/T 10927-1989 | 立轴圆台平面磨床 参数 | Surface grinding machines with vertical grinding wheel spindle and round table - Parameters | |
| 25.080.10 | J53 | GB/T 10929-1989 | 铲齿车床精度 | Relieving lathes - Testing of the accuracy | NEQ ΓOCT 685-83 |
| 25.080.60 | J55 | GB/T 10930-1989 | 花键轴磨床 参数 | Spline shaft grinding machines - Parameters | |
| 25.120.20 | J62 | GB/T 10933-1989 | 闭式双点压力机 精度 | Straight sided two-point mechanical presses - Testing of the accuracy | NEQ JIS B6402-85 |
| 25.100.30 | J41 | GB/T 10944-1989 | 自动换刀机床用7:24圆锥工具柄部40、45和50号圆锥柄 | Tool shanks with 7:24 taper for automatic tool changers - Shanks Nos. 40, 45 and 50 | NEQ ISO 7388/1-83 |
| 25.100.30 | J41 | GB/T 10945-1989 | 自动换刀机床用7:24圆锥工具柄部40、45和50号圆锥柄用拉钉 | Tool shanks with 7:24 taper for automatic tool changers - Retention knobs for shanks Nos. 40, 45 and 50 | NEQ ISO 7388/2-84 |
| 25.100.30 | J41 | GB/T 10946-1989 | 硬质合金锥柄麻花钻 | Taper shank twist drills with carbide tips | NEQ ΓOCT 22736-77 |
| 25.100.30 | J41 | GB/T 10947-1989 | 硬质合金麻花钻通用技术条件 | General technical specifications for twist drill with carbide tips | NEQ ΓOCT 5756-81 |
| 25.100.20 | J41 | GB/T 10948-1989 | 硬质合金直柄T形槽铣刀 | Parallel shank T-slot cutters with carbide tips | NEQ ΓOCT 10673-75 |
| 25.100.20 | J41 | GB/T 10949-1989 | 硬质合金锥柄T形槽铣刀 | Taper shank T-slot cutters with carbide tips | NEQ ΓOCT10673-75 |
| 25.100.20 | J41 | GB/T 10952-1989 | 矩形花键滚刀 | Hobs for parallel side splines | |
| 25.100.10 | J41 | GB/T 10953-1989 | 机夹切断车刀 | Cutting-off tools for turning with clamp tips | NEQ ISO 5610-81 |
| 25.100.10 | J41 | GB/T 10954-1989 | 机夹外螺纹车刀 | Turning tools for external threads with clamp tips | NEQ ISO 5610-81 |
| 25.100.10 | J41 | GB/T 10955-1989 | 机夹内螺纹车刀 | Turning tools for internal threads with clamp tips | NEQ ISO 6261-84 |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.040.40 | N15 | GB/T 11005.1-1989 | DDZ-Ⅲ系列电动单元组合仪表 计算器 | DDZ-Ⅲ series process electronic control system - Computing unit | |
| 25.040.40 | N15 | GB/T 11005.2-1989 | DDZ-Ⅲ系列电动单元组合仪表 调节器 | DDZ-Ⅲ series process electronic control system - Controller | |
| 25.040.40 | N15 | GB/T 11005.3-1989 | DDZ-Ⅲ系列电动单元组合仪表 配电器 | DDZ-Ⅲ series process electronic control system - Distributor | |
| 25.220.40 | H61 | GB/T 11109-1989 | 铝及铝合金阳极氧化 术语 | Anodizing of aluminium and aluminium alloys - Terms | EQV ISO 7583-86 |
| 25.220.40 | H21 | GB/T 11110-1989 | 铝及铝合金阳极氧化 阳极氧化膜的封孔质量的测定方法 导纳法 | Anodizing of aluminium and its alloys - Determination of quality of sealed anodic oxide coatings - Admittance method | EQV ISO 2931-83 |
| 25.220.40 | L10 | GB/T 11250.1-1989 | 复合金属覆层厚度的测定 金相法 | Method for measuring thickness of coated layer on composite metal - The metallographic method | |
| 25.220.40 | L10 | GB/T 11250.2-1989 | 复合金属覆层厚度的测定 X荧光法 | Method for measuring thickness of coated layer on composite metal - The X-ray fluorescent method | |
| 25.220.40 | L10 | GB/T 11250.3-1989 | 复合金属覆镍层厚度的测定 容量法 | Method for measuring thickness of nickel-coated layer on composite metal - The volumetry | |
| 25.220.40 | L10 | GB/T 11250.4-1989 | 复合金属覆铝层厚度的测定 重量法 | Method for measuring thickness of aluminium-coated layer on composite metal - The gravimetric method | |
| 25.100.40 | J43 | GB/T 11270-1989 | 金刚石圆锯片 | Diamond circular saw blades | NEQ ISO 6104-79 |
| 25.040.30 | J07 | GB 11291-1997 | 工业机器人 安全规范 | Industrial robots--Safety specification | EQV ISO 10218:1992 |
| 25.040.20 | L74 | GB/T 11292-1989 | 数字控制机床的数控处理程序 输出2000型记录辅元素 (后置处理命令) | Numerical control of machines-NC processor output - Minor elements of 2000-type records (post-processor commands) | EQV ISO 4343-78 |
| 25.160.40 | H24 | GB/T 11345-1989 | 钢焊缝手工超声波探伤方法和探伤结果分级 | Method for manual ultrasonic testing and classification of testing results for ferritic steel welds | |
| 25.010 | J04 | GB/T 11349.1-1989 | 机械导纳的试验确定 基本定义与传感器 | Experimental determination of mechanical mobility - Basic definitions and transducers | EQV ISO 7626/1-86 |
| 25.010 | J04 | GB/T 11349.2-1989 | 机械导纳的试验确定 用激振器作单点激励测量 | Experimental determination of mechanical mobility - Measurments using single-point translation excitation with and attached vibration exciter | |
| 25.010 | J04 | GB/T 11349.3-1992 | 机械导纳的试验确定 冲击激励法 | Experimental determination of mechanical mobility--Measurements using impact excitation | |
| 25.160.40 | J33 | GB/T 11363-1989 | 钎焊接头强度试验方法 | Methods of the strength tests for brazed and soldered joint | |
| 25.160.20 | J33 | GB/T 11364-1989 | 钎料铺展性及填缝性试验方法 | Test method of spreadability and clearance filling ability for filler metal | |
| 25.220 | A29 | GB/T 11373-1989 | 热喷涂金属件表面预处理通则 | The general principle of surface preparation of metallic substrate for thermal spraying | |
| 25.220 | A29 | GB/T 11374-1989 | 热喷涂涂层厚度的无损测量方法 | Thermal spraying coating Nondestructive methods for measurement of thickness | NEQ ISO 2064-80 |
| 25.220.20 | A29 | GB 11375-1999 | 金属和其他无机覆盖层 热喷涂 操作安全 | Metallic and other inorganic coatings--Thermal spraying--Safe practices | |
| 25.220.40 | A29 | GB/T 11376-1997 | 金属的磷酸盐转化膜 | Phosphate conversion coatings for metals | EQV ISO 9717:1990 |
| 25.220.40 | A29 | GB/T 11377-1989 | 金属和其他无机覆盖层储存条件下腐蚀试验的一般规则 | Metallic and other non-organic coatings-General rules for corrosion tests applicable for storage conditions | EQV ISO 4543-81 |
| 25.220.40 | A29 | GB/T 11378-1989 | 金属覆盖层厚度 轮廓尺寸测量方法 | Metallic coatings-Measurement of coating thickness--Profilometric method | EQV ISO 4518-80 |
| 25.220.40 | A29 | GB/T 11379-1989 | 金属覆盖层 工程用铬电镀层 | Metallic coatings - Electroplated coatings of chromium for engineering purposes | NEQ ISO 6158-84 |
| 25.220.50 | Y26 | GB/T 11418-1989 | 搪瓷耐热性测试方法 | Determination of resistance to heat of vitreous and porcelain enamels | NEQ ISO 4530-83 |
| 25.220.50 | Y26 | GB/T 11419-1989 | 搪瓷耐温急变性测试方法 | Determination of resistance to thermal shock of vitreous and porcelain enamels | NEQ ISO 2747-73 |
| 25.220.50 | Y26 | GB/T 11420-1989 | 搪瓷光泽测试方法 | Measurement of specular gloss of vitreous and porcelain enamels | |
| 25.120.10 | J46 | GB/T 11880-1989 | 模锻锤和大型机械锻压机用模块技术条件 | Large die-blocks used for die-forging hammer and mechanical forging press--Specification | |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.040.20 | L74 | GB/T 12177-1990 | 数子控制机床的数控处理程序输出 逻辑结构 | Numerical control of machines - NC processor output - Logical structure | IDT ISO 3592-78 |
| 25.010;
25. |
J50 | GB/T 12217-1990 | 机器 轴高 | Machines - Shaft heights | NEQ ISO 496-73 |
| 25.220.40 | A29 | GB/T 12305.6-1997 | 金属覆盖层 金和金合金电镀层的试验方法 第六部分：残留盐的测定 | Metallic coating--Test methods for electrodeposited gold and gold alloy coatings-Part 6: Determination of the presence of residual salts | EQV ISO 4524-6:1988 |
| 25.220.40 | A29 | GB/T 12307.3-1997 | 金属覆盖层 银和银合金电镀层的试验方法 第三部分：残留盐的测定 | Metallic coatings--Test methods for electrodeposited silver and silver alloy coatings--Part 3: Determination of the presence of residual salts | EQV ISO 4522-3:1988 |
| 25.220.40 | A29 | GB/T 12333-1990 | 金属覆盖层 工程用铜电镀层 | Metallic coatings - Electroplated coatings of copper for engineering purposes | |
| 25.220.40 | A29 | GB/T 12332-1990 | 金属覆盖层 工程用镍电镀层 | Metallic coatings - Electroplated coatings of nickel for engineering purposes | EQV ISO 4526-84 |
| 25.220.40 | A29 | GB/T 12334-2001 | 金属和其他非有机覆盖层--关于厚度测量的定义和一般规则 | Metallic and other inorganic coatings--Definitions and conventions concerning the measurement of thickness | IDT ISO 2064:1996 |
| 25.220.40 | A29 | GB/T 12335-1990 | 金属覆盖层 对底材呈阳极性的覆盖层腐蚀试验后的试样评级 | Metallic coatings - Coatings anodic to the substrate - Rating of test specimens subjected to corrosion tests | |
| 25.160.01 | J33 | GB/T 12467.1-1998 | 焊接质量要求 金属材料的熔化焊 第一部分: 选择及使用指南 | Quality requirements for welding--Fusion welding of metallic materials--Part 1: Guidelines for selection and use | IDT 3834.1-1994 |
| 25.160.01 | J33 | GB/T 12467.2-1998 | 焊接质量要求 金属材料的熔化焊 第二部分: 完整质量要求 | Quality requirements for welding--Fusion welding of metallic materials--Part 2: Comprehensive quality requirements | IDT ISO 3834.2-1994 |
| 25.160.01 | J33 | GB/T 12467.3-1998 | 焊接质量要求 金属材料的熔化焊 第三部分: 一般质量要求 | Quality requirements for welding--Fusion welding of metallic materials--Part 3: Standards quality requirements | IDT ISO 3834.3-1994 |
| 25.160.01 | J33 | GB/T 12467.4-1998 | 焊接质量要求 金属材料的熔化焊 第四部分: 基本质量要求 | Quality requirements for welding--Fusion welding of metallic materials--Part 4: Elementary quality requirements | |
| 25.160 | J33 | GB/T 12469-1990 | 焊接质量保证 钢熔化焊接头的要求和缺陷分级 | Quality assurance of welding？Requirement for fusion welding joint of steel and classification for imperfection | NEQ DIN 8563 T3-79 |
| 25.160.20 | J33 | GB/T 12470-1990 | 低合金钢埋弧焊用焊剂 | Fluxes for the submerged arc welding of low alloy steel | NEQ ANSI/AWS A5.23-80 |
| 25.120.30 | Y99 | GB/T 12554-1990 | 塑料注射模技术条件 | Specification of injection mould for plastics | |
| 25.120.30 | Y99 | GB/T 12555.1-1990 | 塑料注射模大型模架 标准模架 | Injection mould for plastic large-size mould bases - Standard mould bases | |
| 25.120.30 | Y99 | GB/T 12555.2-1990 | 塑料注射模大型模架 技术条件 | Injection mould for plastic large-size mould bases - Specification | |
| 25.120.30 | Y99 | GB/T 12555.3-1990 | 塑料注射模大型模架 座板 | Injection mould for plastic large-size mould bases - Elamping plates | |
| 25.120.30 | Y99 | GB/T 12555.4-1990 | 塑料注射模大型模架 模板 | Injection mould for plastic large-size mould bases - Mould plates | |
| 25.120.30 | Y99 | GB/T 12555.5-1990 | 塑料注射模大型模架 支承板 | Injection mould for plastic large-size mould bases - Support plates | |
| 25.120.30 | Y99 | GB/T 12555.6-1990 | 塑料注射模大型模架 推板 | Injection mould for plastic large-size mould bases - Ejector plates | |
| 25.120.30 | Y99 | GB/T 12555.7-1990 | 塑料注射模大型模架 垫块 | Injection mould for plastic large-size mould bases - Spacer plates | |
| 25.120.30 | Y99 | GB/T 12555.8-1990 | 塑料注射模大型模架 带头导柱 | Injection mould for plastic large-size mould bases - Guide pillars with head | |
| 25.120.30 | Y99 | GB/T 12555.9-1990 | 塑料注射模大型模架 有肩导柱 | Injection mould for plastic large-size mould bases - Guide pillars with shoulder | |
| 25.120.30 | Y99 | GB/T 12555.10-1990 | 塑料注射模大型模架 推板导柱 | Injection mould for plastic large-size mould bases - Guide pins for ejector plater | |
| 25.120.30 | Y99 | GB/T 12555.11-1990 | 塑料注射模大型模架 直导套 | Injection mould for plastic large-size mould bases - Straight guide bushes | |
| 25.120.30 | Y99 | GB/T 12555.12-1990 | 塑料注射模大型模架 推板导套 | Injection mould for plastic large-size mould bases - Guide bushes with head | |
| 25.120.30 | Y99 | GB/T 12555.13-1990 | 塑料注射模大型模架 复位杆 | Injection mould for plastic large-size mould bases - Return pins | |
| 25.120.30 | Y99 | GB/T 12555.14-1990 | 塑料注射模大型模架 衬套 | Injection mould for plastic large-size mould bases - Iiner bushes | |
| 25.120.30 | Y99 | GB/T 12556.1-1990 | 塑料注射模中小型模架 | Injection mould for plastic--Medium size and small size mould bases | |
| 25.120.30 | Y99 | GB/T 12556.2-1990 | 塑料注射模中小型模架技术条件 | Injection mould for plastic - Specifications for medium size and small size mould bases | |
| 25.220.40 | A29 | GB/T 12599-1990 | 金属覆盖层 锡电镀层 | Metallic coatings - Electroplated coatings of tin | IDT ISO 2093-86 |
| 25.220.40 | A29 | GB/T 12600-1990 | 金属覆盖层 塑料上铜+镍+铬电镀层 | Metallic coatings - Electroplated coatings of copper plus nickel plus chromium on plastics materials | IDT ISO 4525-85 |
| 25.200 | J36 | GB/T 12603-1990 | 金属热处理工艺分类及代号 | Classification and designation on metal heat treatment | |
| 25.160.40 | H26 | GB/T 12605-1990 | 钢管环缝熔化焊对接接头射线透照工艺和质量分级 | Methods of radiographic inspection and quality classification of circumferential fusion welded butt joints in steel pipes and tubes | NEQ ISO 1106/3-84 |
| 25.220 | A29 | GB/T 12607-1990 | 热喷涂涂层设计命名方法 | Designation for the design of thermal spraying coatings | |
| 25.220 | A29 | GB/T 12608-1990 | 热喷涂涂层材料命名方法 | Designation of the materials for thermal spraying coatings | |
| 25.220.40 | A29 | GB/T 12609-1990 | 电沉积金属覆盖层和有关精饰计数抽样检查程序 | Electrodeposited metallic coatings and related finishes - Sampling procedures for inspection by attributes | IDT ISO 4519-80 |
| 25.220.40 | A29 | GB/T 12610-1990 | 塑料上电镀层 热循环试验 | Electroplated coatings on plastics materials - Thermal cycling test | NEQ ISO 4525-85 |
| 25.220.40 | A29 | GB/T 12611-1990 | 金属零(部)件镀覆前质量控制技术要求 | Technical requirements of quality control for metal parts to be coated | |
| 25.220.20 | A29 | GB/T 12612-1990 | 多功能钢铁表面处理液通用技术条件 | General specification for multifunctional solution of steel and iron surface treatment | |
| 25.040.30 | J28 | GB/T 12642-2001 | 工业机器人 性能规范及其试验方法 | Industrial robots--Performance criteria and related test methods | EQV ISO 9283:1998 |
| 25.040.30 | J07 | GB/T 12643-1997 | 工业机器人 词汇 | Industrial robots--Vocabulary | EQV ISO 8373:1994 |
| 25.040.30 | J28 | GB/T 12644-2001 | 工业机器人 特性表示 | Industrial robots--Presentation of characteristics | EQV ISO 9946:1999 |
| 25.040.20 | L74 | GB/T 12646-1990 | 数字控制机床的数控处理程序输入 基本零件源程序参考语言 | Numerical control of machines - NC processor input - Basic part program reference language | EQV ISO 4342-85 |
| 25.220.40 | H21 | GB/T 12967.1-1991 | 铝及铝合金阳极氧化 用喷磨试验仪测定阳极氧化膜的平均耐磨性 | Anodizing of aluminium and aluminium alloys - Measurement of mean specific adrasion resistance of anodic oxidation coatings with an adrasive jet test apparatus | IDT ISO 8252-87 |
| 25.220.40 | H21 | GB/T 12967.2-1991 | 铝及铝合金阳极氧化 用轮式磨损试验仪测定阳极氧化膜的耐磨性和磨损系数 | Anodizing of aluminium and aluminium alloys - Measurement of wear resistance and wear index of anodic oxidation coatings with an abrasive wheel wear test apparatus | IDT ISO 8251-87 |
| 25.220.40 | H21 | GB/T 12967.3-1991 | 铝及铝合金阳极氧化 氧化膜的铜加速醋酸盐雾试验 (CASS试验) | Anodizing of aluminium and aluminium alloys - Copper accelerated acetic acid salt spray test for anodic oxide coatings (CASS test) | IDT ISO 3770-76 |
| 25.220.40 | H21 | GB/T 12967.4-1991 | 铝及铝合金阳极氧化 着色阳极氧化膜耐紫外光性能的测定 | Anodizing of aluminium and aluminium alloys - Determination of the fastness to ultraviolet light of coloured anodic oxide coatings | IDT ISO 6581-80 |
| 25.220.40 | H21 | GB/T 12967.5-1991 | 铝及铝合金阳极氧化 用变形法评定阳极氧化膜的抗破裂性 | Anodizing of aluminium and aluminium alloys - Assessment of resistance of anodic oxide coatings to cracking by deformation | IDT ISO 3211-77 |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.160.30 | J64 | GB/T 13164-1991 | 埋弧焊机 | Submerged arc welding machine | |
| 25.160.30 | J64 | GB/T 13165-1991 | 电弧焊机噪声测定方法 | Determination for noise emitted by arc welding machines | |
| 25.220.40 | H23 | GB/T 13222-1991 | 金属热喷涂层剪切强度的测定 | Thermal sprayed metallic coatings - Determination of shear strength | |
| 25.040.40 | N10 | GB/T 13283-1991 | 工业过程测量和控制用检测仪表和显示仪表精确度等级 | Accuracy class of measuring instruments and display instruments for industrial process measurement and control | |
| 25.220 | H72 | GB/T 13292-1991 | 涂层硬质合金分类和涂层主要技术要求 | Classification of coated hardmetal and main technical specifications for coating | |
| 25.160.40 | J33 | GB/T 13311-1991 | 锅炉受压元件焊接接头机械性能试验方法 | Boiler pressure parts - Mechanical test for welded joints | |
| 25.220 | H25 | GB/T 13312-1991 | 钢铁件涂装前除油程度检验方法 (验油试纸法) | The standard method of identification of degreaasing degree on the steel surfaces before covering organic coatings (Test paper method) | |
| 25.220.40 | A29 | GB/T 13322-1991 | 金属覆盖层 低氢脆镉钛电镀层 | Metal coating - Cd-Ti plating of low hydrogan embrittlement | |
| 25.200 | J66 | GB/T 13324-1991 | 热处理设备术语 | Terminology of heat treatment installation | |
| 25.220.40 | A29 | GB/T 13346-1992 | 金属覆盖层 钢铁上的镉电镀层 | Metallic coatings？Electroplated coatings of cadmium on iron and steel | IDT ISO 2082-86 |
| 25.040.40 | N18 | GB/T 13423-1992 | 工业控制用软件评定准则 | Criteria for the evaluation of software used for industry control | |
| 25.160.40 | J33 | GB/T 13450-1992 | 对接焊接头宽板拉伸试验方法 | Method of wide plate tension test for butt welded joint | NEQ JIS Z3127-77 |
| 25.140 | J47 | GB/T 13473-1992 | 钢锤通用技术条件 | Steel hammers - General technical requirements | |
| 25.220.50 | Y26 | GB/T 13484-1992 | 接触食物搪瓷制品 | Enamelled ware in contact with food | |
| 25.220.50 | Y26 | GB/T 13485-1992 | 接触食物搪瓷制品铅、镉析出量测试方法 | Standard test method for lead and cadmium released from enamelled ware in contact with food | |
| 25.180.10 | K60 | GB/T 13535-1992 | 电热用等离子设备试验方法 | Test methods of plasma installations for electroheat applications | NEQ IEC 60680-80 |
| 25.080 | J50 | GB/T 13574-1992 | 金属切削机床 静刚度检验通则 | Metal-cutting machine tools - Test code for static rigidity | |
| 25.040.40 | N14 | GB/T 13639-1992 | 工业过程测量和控制系统用模拟输入数字式指示仪 | Digital indicators with analogue input for use in industrial-process measurement and control systems | |
| 25.160.20 | J33 | GB/T 13679-1992 | 锰基钎料 | Manganese base brazing filler metals | |
| 25.220.40 | A29 | GB/T 13744-1992 | 磁性和非磁性基体上镍电镀层厚度的测量 | The measurement of coating thickness for electrodeposited nickel coatings on magnetic and non-magnetic substracts | IDT ISO 2361-82 |
| 25.160.20 | J33 | GB/T 13814-1992 | 镍及镍合金焊条 | Nickel and nickel alloy covered welding electrodes | IDT ANSI/AWSAS.11-89 |
| 25.160.20 | J33 | GB/T 13815-1992 | 铝基钎料 | Aluminium base brazing filler metals | NEQ JIS Z 3263-80 |
| 25.160.40 | J33 | GB/T 13816-1992 | 焊接接头脉动拉伸疲劳试验方法 | Test method for pulsed tensile fatigue of welded joints | NEQ JIS Z 3103-1976 |
| 25.160.40 | J33 | GB/T 13817-1992 | 对接接头刚性拘束焊接裂纹试验方法 | Method of rigid restraint cracking test for welding butt joint | |
| 25.220.40 | A29 | GB/T 13825-1992 | 金属覆盖层 黑色金属材料热镀锌层的质量测定 称量法 | Metallic coatings--Determination of the mass for hot dip galvanized coatings on ferrous materials--Gravimetric method | NEQ ISO 1460-73(E) |
| 25.100.70 | J43 | GB/T 13826-1992 | 湿式(非金属类)摩擦材料 | Wet type (non-metallic)friction materials | |
| 25.220.40 | A29 | GB/T 13911-1992 | 金属镀覆和化学处理表示方法 | Expression methods for metallic coating and chemical treatment | |
| 25.220.40 | A29 | GB/T 13912-1992 | 金属覆盖层 钢铁制品热镀锌层 技术要求 | Metallic coatings--Hot dip galvanized coatings on fabricated ferrous products--Specification | NEQ ISO 1459-73(E) |
| 25.220.40 | A29 | GB/T 13913-1992 | 自催化镍-磷镀层 技术要求和试验方法 | Autocatalytic nickel-phosphorus coating--Specification and test methods | NEQ ISO 4527-87 |
| 25.140.20 | K64 | GB/T 13956-1992 | 电动工具控制仪的安全 | Safety of controllers for electric tools | |
| 25.140.20 | K09 | GB 13960-1992 | 可移式电动工具的安全 第一部分: 一般要求 | Safety of transportable motor-operated electric tools--Part 1: General requirements | IDT IEC 61029-1-90 |
| 25.140.20 | K64 | GB 13960.2-1996 | 可移式电动工具的安全 圆锯的专用要求 | Safety of transportable motor-operated electric tools--Particular requirements for circular saws | IDT IEC 61029-2-1:1993 |
| 25.140.20 | K64 | GB 13960.3-1996 | 可移式电动工具的安全 摇臂锯的专用要求 | Safety of transportable motor-operated electric tools--Particular requirements for radial arm saws | IDT IEC 61029-2-2-1993 |
| 25.140.20 | K64 | GB 13960.4-1996 | 可移式电动工具的安全 平刨和厚度刨的专用要求 | Safety of transportable motor-operated electric tools--Particular requirements for planers and thicknessers | IDT IEC 61029-2-3-1993 |
| 25.140.20 | K64 | GB 13960.5-1996 | 可移式电动工具的安全 台式砂轮机的专用要求 | Safety of transportable motor-operated electric tools--Particular requirements for bench grinders | IDT IEC 61029-2-4-1993 |
| 25.140.20 | K64 | GB 13960.6-1996 | 可移式电动工具的安全 带锯的专用要求 | Safety of transportable motor-operated electric tools--Particular requirements for band saws | EQV IEC 61029-2-5-1993 |
| 25.140.20 | K64 | GB 13960.7-1997 | 可移式电动工具的安全 第二部分: 带水源金刚石钻的专用要求 | Safety of transportable motor-operated electric tools--Part 2: Particular requirements for diamond drills with water supply | IDT IEC 61029-2-6:1993 |
| 25.140.20 | K64 | GB 13960.8-1997 | 可移式电动工具的安全 第二部分: 带水源金刚石锯的专用要求 | Safety of transportable motor-operated electric tools--Part 2: Particular requirements for diamond saws with water supply | IDT IEC 61029-2-7:1993 |
| 25.140.20 | K64 | GB 13960.9-1997 | 可移式电动工具的安全 第二部分: 斜切割机的专用要求 | Safety of transportable motor-operated electric tools--Part 2: Particular requirements for mitre saws | IDT IEC 61029-2-9:1993 |
| 25.140.20 | K64 | GB 13960.10-1998 | 可移式电动工具的安全 第二部分: 单轴立式木铣的专用要求 | Safety of transportable motor-operated electric tools Part 2: Particular requirements for single spindle vertical moulders | IDT IEC 61029-2-8:1993 |
| 25.140.20 | K64 | GB 13960.11-2000 | 可移式电动工具的安全 第二部分: 型材切割机的专用要求 | Safety transportable motor-operated electric tools Part 2: Particular requirements for cutting-off grinders | IDT IEC 61029-2-10:1998 |
| 25.140.20 | K64 | GB 13960.12-2001 | 可移式电动工具的安全 第二部分: 高压清洗机的专用要求 | Safety of transportable motor-operated electric tools Part 2: Particular requirements for high pressure cleaners | |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.010 | Y90 | GB/T 14253-1993 | 轻工机械通用技术条件 | General specifications for light industry machinery | |
| 25.040.30 | J28 | GB/T 14283-1993 | 点焊机器人通用技术条件 | General specifications of spot-welding robots | |
| 25.040.30 | J28 | GB/T 14284-1993 | 工业机器人通用技术条件 | Industrial robots--General specifications | |
| 25.100.10 | J41 | GB/T 14297-1993 | 可转位内孔车刀 | Boring bars for indexable inserts | |
| 25.100.20 | J41 | GB/T 14298-1993 | 可转位螺旋立铣刀 | Helical end milling cutters with indexable inserts | |
| 25.100.30 | J41 | GB/T 14299-1993 | 可转位螺旋沟浅孔钻 | Spiral flute drill with indexable inserts | |
| 25.080.40 | J41 | GB/T 14300-1993 | 可转位直沟浅孔钻 | Straight flute drill with indexable inserts | |
| 25.100.20 | J41 | GB/T 14301-1993 | 整体硬质合金锯片铣刀 | Solid carbide slitting cutters | |
| 25.080.25 | J57 | GB/T 14302-1993 | 牛头刨床 精度 | shaping machines--Testing of the accuracy | |
| 25.100.70 | J43 | GB/T 14319-1993 | 超精油石 | Superfinishing stone | |
| 25.100.70 | J43 | GB/T 14320-1993 | 陶瓷结合剂强力珩磨油石 | Vitrified force-honing stone | NEQ ISO 3920;
ISO 3921 |
| 25.100.70 | J43 | GB/T 14321-1993 | 刚玉磨料中α-Al2O3相X射线定量测定方法 | Testing method for quantities of α-Al2O3 phase in alumina with an X-ray diffractometer | |
| 25.100.70 | J43 | GB/T 14322-1993 | 普通磨料精微粉(W3.5 - W0.5)粒度组成测定方法 | Determination for grain size distribution of microgrits W3.5 to W0.5 of conventional abrasive | |
| 25.100.20 | J41 | GB/T 14328.1-1993 | 直柄粗加工立铣刀 型式与尺寸 | Roughing end mill with parallel shank types and dimensions | NEQ ISO 3338 |
| 25.100.20 | J41 | GB/T 14328.2-1993 | 削平型直柄粗加工立铣刀 型式与尺寸 | Roughing end mill with flatted parallel shank types and dimensions | NEQ ISO 3338 |
| 25.100.20 | J41 | GB/T 14328.3-1993 | 莫氏锥柄粗加工立铣刀 型式与尺寸 | Roughing end mill with morse taper shank types and dimensions | NEQ ISO 3338 |
| 25.100.20 | J41 | GB/T 14328.4-1993 | 粗加工立铣刀 技术条件 | Roughing end mills technical specifications | NEQ ISO 3338 |
| 25.100.25 | J41 | GB/T 14329.1-1993 | 平刀体键槽拉刀 型式与尺寸 | Flat body keyway broach types and dimensions | |
| 25.100.25 | J41 | GB/T 14329.2-1993 | 加宽平刀体键槽拉刀 型式与尺寸 | Widened flat body keyway broach types and dimensions | |
| 25.100.25 | J41 | GB/T 14329.3-1993 | 带倒角齿键槽拉刀 型式与尺寸 | Keyway broach with chamfer types and dimensions | |
| 25.100.25 | J41 | GB/T 14329.4-1993 | 键槽拉刀通用技术条件 | Technical specifications for keyway broaches | |
| 25.100.20 | J41 | GB/T 14330-1993 | 硬质合金机夹三面刃铣刀 | Machanically clamped carbide side milling cutters | |
| 25.060 | J62 | GB/T 14331-1993 | 自动卷簧机 精度 | Automatic spring winding machine--Testing of the accuracy | NEQ гOCT 10712-74 |
| 25.100.30 | J41 | GB/T 14332-1993 | 硬质合金喷吸钻 | Ejector drills with carbide tips | |
| 25.100 | J41 | GB/T 14333-1993 | 盘形剃齿刀 | Rotary gear shaving cutters | |
| 25.120.10 | J62 | GB/T 14347-1993 | 开式压力机 型式与基本参数 | Open front mechanical power presses--Types and basic parameters | NEQ ISO 6898-1984 |
| 25.100.20 | J41 | GB/T 14348.1-1993 | 双圆弧齿轮滚刀 型式和尺寸 | The basic types and dimensions of hobs for double--circular-arc gear | |
| 25.100.20 | J41 | GB/T 14348.2-1993 | 双圆弧齿轮滚刀 技术条件 | The general technical specifications of hobs for double circular-arc gear | |
| 25.120.20 | J62 | GB/T 14349-1993 | 板料折弯机 精度 | Press brake--Testing of the accuracy | |
| 25.120.10 | J62 | GB/T 14404-1993 | 剪板机 精度 | Plate shear--Testing of the accuracy | NEQ DIN 55804-79 |
| 25.040.30 | J28 | GB/T 14468.1-1993 | 工业机器人 圆形机械接口 | Industrial robots--Circular mechanical interface | NEQ ISO 9409.1 |
| 25.040.30 | J28 | GB/T 14468.2-1999 | 工业机器人 轴形机械接口 | Industrial robots--Shaft mechanical interface | EQV ISO 9409-2:1996 |
| 25.140.20 | K64 | GB/T 14469-2001 | 电喷枪 | Electric spray guns | |
| 25.060.10 | J52 | GB/T 14534-1993 | 电磁吸盘 | Electromagnetic chuck | |
| 25.080.10 | J53 | GB/T 14535-1993 | 单轴自动车床 精度 | Single spindle automatic lathes--Testing of the accuracy | |
| 25.040.20 | J54 | GB/T 14660-1993 | 数控坐标镗床 精度 | NC jig boring machine--Testing of the accuracy | |
| 25.060.20 | J41 | GB/T 14661-1993 | 可转位A型刀夹 | Type A cartridges for indexable inserts | NEQ ISO 5611-89 |
| 25.120.30 | J46 | GB/T 14662-1993 | 冲模技术条件 | Specification of the press tools | |
| 25.120.30 | K15 | GB/T 14663-1993 | 塑封模具技术条件 | Specification of plastic packaging mould | |
| 25.120.30 | K15 | GB/T 14664-1993 | 塑封模具尺寸公差规定 | Dimensional tolerances stipulation of plastic packaging mould | |
| 25.160.40 | H26 | GB/T 14693-1993 | 焊缝无损检测符号 | Nondestructive testing symbols for welds | |
| 25.140 | J47 | GB/T 14764-1993 | 手用钢锯条 | Hand hacksaw blades | |
| 25.140 | J47 | GB/T 14765-1993 | 十字柄套筒扳手 | Four-way socket wrenches | NEQ ISO 6788-82 |
| 25.180.10 | K61 | GB/T 14809-2000 | 高频介质加热设备输出功率的测定方法 | High-frequency dielectric heating installations-Test methods of the determination of power output | EQV IEC 61308:1994 |
| 25.100.20 | J41 | GB/T 14895-1994 | 金属切削刀具术语 切齿刀具 | Terms in metal cutting tools--Gear cutters | NEQ JIS B0174-78 |
| 25.080 | J59 | GB/T 14896.1-1994 | 特种加工机床 术语 基本术语 | Non-traditional machine tools--Terminology--Basic terminology | |
| 25.080 | J59 | GB/T 14896.2-1994 | 特种加工机床 术语 放电加工机床 | Non-traditional machine tools--Terminology--Electro-discharge machine tools | |
| 25.080 | J59 | GB/T 14896.3-1994 | 特种加工机床 术语 电解加工机床 | Non-traditional machine tools--Terminology--Electrolytic machine tools | |
| 25.080 | J59 | GB/T 14896.4-1994 | 特种加工机床 术语 超声加工机床 | Non-traditional machine tools--Terminology--Ultrasonic machine tools | |
| 25.080 | J59 | GB/T 14896.5-1994 | 特种加工机床 术语 复合加工机床 | Non-traditional machine tools--Terminology--Combined machining machine tools | |
| 25.080 | J59 | GB/T 14896.6-1994 | 特种加工机床 术语 其他特种加工机床 | Non-traditional machine tools--Terminology--Other non-traditional machine tools | |
| 25.220.40 | H12 | GB/T 14952.1-1994 | 铝及铝合金阳极氧化 阳极氧化膜的封孔质量评定 磷-铬酸法 | Anodizing of aluminium and its alloys--Assessment of quality of sealed anodic oxide coatings by measurement of the loss of mass after immersion in phosphoric-chromic acid solution | EQV ISO 3210-83 |
| 25.220.40 | H12 | GB/T 14952.2-1994 | 铝及铝合金阳极氧化 阳极氧化膜的封孔质量评定 酸浸法 | Anodizing of aluminium and its alloys--Assessment of sealing quality by measurement of the loss of mass after immersion in acid solution | EQV ISO 2932-81 |
| 25.220.40 | H12 | GB/T 14952.3-1994 | 铝及铝合金阳极氧化 着色阳极氧化膜色差和外观质量检验方法 目视观察法 | Anodizing of aluminium and its alloys--Determination of color differences and appearance of colored anodic oxide films--Viewing method | |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.160.40 | J33 | GB/T 15111-1994 | 点焊接头剪切拉伸疲劳试验方法 | Test method for shear tensile fatigue of spot welded joints | |
| 25.100.70 | J43 | GB/T 15305.1-1994 | 涂附磨具 页状砂布砂纸 尺寸和公差 | Coated abrasives--Abrasive sheets--Dimensions and tolerances | |
| 25.100.70 | J43 | GB/T 15305.2-1994 | 涂附磨具 卷状砂布 砂纸 尺寸和公差 | Coated abrasives--Abrasive rolls--Dimensions and tolerances | |
| 25.100.70 | J41 | GB/T 15305.3-1994 | 涂附磨具 砂带 尺寸和公差 | Coated abrasives--Abrasive belts--Dimensions and tolerances | EQV ISO 1929-93 |
| 25.100.70 | J43 | GB/T 15305.4-1994 | 涂附磨具 砂盘 尺寸和公差 | Coated abrasives--Abrasive discs--Dimensions and tolerances | NEQ ISO 3017-81 |
| 25.100 | J41 | GB/T 15306.1-1994 | 陶瓷可转位刀片 无孔刀片尺寸(G级) | Indexable inserts for cutting tools--Ceramic inserts with rounded corners--Dimensions of inserts without fixing hole(Class G) | EQV ISO 9361-1-91 |
| 25.100 | J41 | GB/T 15306.2-1994 | 陶瓷可转位刀片 带孔刀片尺寸 | Indexable inserts for cutting tools--Ceramic inserts with rounded corners--Dimensions of inserts with cylindrical fixing hole | EQV ISO 9361-2-91 |
| 25.100 | J41 | GB/T 15306.3-1994 | 陶瓷可转位刀片 无孔刀片尺寸(U级) | Indexable inserts for cutting tools--Ceramic inserts with rounded corners--Dimensions of inserts without fixing hole(Class U) | |
| 25.100 | J41 | GB/T 15306.4-1994 | 陶瓷可转位刀片 技术条件 | Indexable inserts for cutting tools--Ceramic inserts with rounded corners--Specifications | |
| 25.100 | J41 | GB/T 15307-1994 | 可转位钻头用削平型直柄 | Drills with indexable inserts--Cylindrical shanks with a parallel flat | IDT ISO 9766-90 |
| 25.040 | L60 | GB/T 15312-1994 | 制造业自动化 术语 | Terminology of automation for manufacturing | |
| 25.080 | J50 | GB/T 15375-1994 | 金属切削机床 型号编制方法 | Metal-cutting machine tools--Method of type designation | |
| 25.220.40 | H49 | GB/T 15393-1994 | 钢丝镀锌层 | Zinc coatings for steel wire | NEQ ISO 7989-88 |
| 25.120.30 | Y99 | GB/T 12555.15-1990 | 塑料注射模大型模架 限位块 | Injection mould for plastic large-size mould bases？Stop plates | |
| 25.160.30 | J64 | GB 15578-1995 | 电阻焊机的安全要求 | Safety requirements for resistance welding machine | |
| 25.160.30 | J64 | GB 15579-1995 | 弧焊设备安全要求 第1部分:焊接电源 | Safety requirements for arc welding equipment--Part 1: Welding power sources | IDT IEC 60974/1-1989 |
| 25.160.30 | J64 | GB 15579.11-1998 | 弧焊设备安全要求 第11部分: 电焊钳 | Safety requirements for are welding equipment Part 11: Electrode holders | EQV IEC 60974/11-1992 |
| 25.160.30 | J64 | GB 15579.12-1998 | 弧焊设备安全要求 第12部分: 焊接电缆耦合装置 | Safety requirements for arc welding equipment Part 12: Coupling devices for welding cables | EQV IEC 60974/12-1992 |
| 25.220.40 | A83 | GB/T 15717-1995 | 真空金属镀层厚度测试方法 电阻法 | Test method for vacuum-deposited metal thickness--Electric resistance method | |
| 25.140 | J47 | GB/T 15729-1995 | 扭力扳手通用技术条件 | Torque wrench--General requirements | EQV ISO 6789-1992 |
| 25.140 | J47 | GB/T 15730-1995 | 电讯夹扭钳和剪切钳通用技术条件 | Pliers and nippers for electronics--General technical requirements | EQV ISO 9657-1989 |
| 25.200 | J36 | GB 15735-1995 | 金属热处理生产过程安全卫生要求 | Requirements for the safety and health in production process of metal heat treatment | |
| 25.160.40 | J33 | GB/T 15747-1995 | 正面角焊缝接头拉伸试验方法 | Method of tension test for front fillet welded joint | NEQ JIS Z3131-1976 |
| 25.060 | J50 | GB 15760-1995 | 金属切削机床安全防护通用技术条件 | Metal-cutting machine tools--General safeguarding specification | |
| 25.220.40 | A29 | GB/T 15821-1995 | 金属覆盖层 延展性测量方法 | Metallic coatings--Methods of measurement of ductility | EQV ISO 8401-1986 |
| 25.010 | J32 | GB/T 15826.1-1995 | 锤上钢质自由锻件机械加工余量与公差一般要求 | Machining allowances and tolerances for steel open die forgings on hammer--General reguirement | EQV DIN 7527 |
| 25.010 | J32 | GB/T 15826.2-1995 | 锤上钢质自由锻件机械加工余量与公差盘、柱类 | Machining allowances and tolerances for steel open die forgings on hammer--Disks and columns | EQV DIN 7527 |
| 25.010 | J32 | GB/T 15826.3-1995 | 锤上钢质自由锻件机械加工余量与公差 带孔圆盘类 | Machining allowances and tolerances for steel open die forgings on hammer--Disk swith holes | EQV DIN 7527 |
| 25.010 | J32 | GB/T 15826.4-1995 | 锤上钢质自由锻件机械加工余量与公差 圆环类 | Machining allowances and tolerances for steel open die forgings on hammer--Rings | EQV DIN 7527 |
| 25.010 | J32 | GB/T 15826.5-1995 | 锤上钢质自由锻件机械加工余量与公差 套筒类 | Machining allowances and tolerances for steel open die forgings on hammer--Seamles cylinder hushings | EQV DIN 7527 |
| 25.010 | J32 | GB/T 15826.6-1995 | 锤上钢质自由锻件机械加工余量与公差 光轴类 | Machining allowances and tolerances for steel open die forgings on hammer--Shaft without steps | EQV DIN 7527 |
| 25.010 | J32 | GB/T 15826.7-1995 | 锤上钢质自由锻件机械加工余量与公差 台阶轴类 | Machining allowances and tolerances for steel open die forgings on hammer--Shaft with steps | EQV DIN 7527 |
| 25.010 | J32 | GB/T 15826.8-1995 | 锤上钢质自由锻件机械加工余量与公差 单拐曲轴类 | Machining allowances and tolerances for steel open dle forgings on hammer--Single throw crankshaft | EQV DIN 7527 |
| 25.010 | J32 | GB/T 15826.9-1995 | 锤上钢质自由锻件机械加工余量与公差 黑皮锻件 | Machining allowances and tolerances for steel open die forgings on hammer--Forging without machining | EQV DIN 7527 |
| 25.220.30 | A29 | GB/T 15827-1995 | 离子镀 仿金氮化钛的颜色 | Ion plating--Colour of golden TiN | NEQ ISO 8654-1987 |
| 25.160.20 | J33 | GB/T 15829.1-1995 | 软钎焊用钎剂 分类、标记与包装 | Soldering fluxes--Classification, labelling and packaging | EQV ISO 9454/1-1990 |
| 25.160.20 | J33 | GB/T 15829.2-1995 | 软钎焊用钎剂 树脂类钎剂 | Soldering fluxes--Resin basis fluxes | |
| 25.160.20 | J33 | GB/T 15829.4-1995 | 软钎焊用钎剂 无机物类钎剂 | Soldering fluxes--Inorganic fluxes | |
| 25.160.20 | J33 | GB/T 15829.3-1995 | 软钎焊用钎剂 有机物类钎剂 | Soldering fluxes--Organic fluxes | |
| 25.160.40 | J04 | GB/T 15830-1995 | 钢制管道对接环焊缝超声波探伤方法和检验结果的分级 | Methods of ultrasonic inspection and result classification of circumferential butt welds in steel pipes and tubes | NEQ BS 3923-86 |
| 25.040 | L85 | GB/T 15946-1995 | 可程控测量设备的标准数字接口 | Standard digital interface for programmable instrumentation | IDT IEEE 488.1-87 |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.140 | J47 | GB/T 16452-1996 | 电讯夹扭钳和剪切钳术语 | Pliers and nippers for electronics--Nomenclature | IDT ISO 8979-1988 |
| 25.080.60 | J09 | GB 16454-1996 | 锯床 安全防护技术要求 | Sawing machines--Safeguarding specification | |
| 25.100.20 | J41 | GB/T 16456.1-1996 | 硬质合金螺旋齿立铣刀 第1部分：直柄立铣刀 型式和尺寸 | End mills with brazed helical hardmetal tips--Part 1: Dimensions of end mills with parallel shank | IDT ISO 10145-1-1993 |
| 25.100.20 | J41 | GB/T 16456.2-1996 | 硬质合金螺旋齿立铣刀 第2部分: 7: 24锥柄立铣刀 型式和尺寸 | End mills with brazed helical hardmetal tips--Part 2: Dimensions of end mills with 7:24 taper shank | IDT ISO 10145-2-1993 |
| 25.100.20 | J41 | GB/T 16456.3-1996 | 硬质合金螺旋齿立铣刀 第3部分: 莫氏锥柄立铣刀 型式和尺寸 | End mills with brazed helical hardmetal tips--Part 3: Dimensions of end mills with morse taper shank | NEQ NF E66-280-84 |
| 25.100.20 | J41 | GB/T 16456.4-1996 | 硬质合金螺旋齿立铣刀 第4部分: 技术条件 | End mills with brazed helical hardmetal tips--Part 4: Technical specifications | NEQ JIS B 4114-83 |
| 25.100.40 | J43 | GB/T 16457-1996 | 超硬磨料制品 切割石材和建筑物用锯片 钢基体尺寸 | Abrasive products--Segmented saws for machining of stone and masonry cutting--Dimensions of steel blades | IDT ISO 6105-1988 |
| 25.100.70 | J43 | GB/T 16458.1-1996 | 磨料磨具术语 第1部分: 磨料术语 | Terminologry for abrasives and abrasive products--Part 1: Terminology for abrasives | |
| 25.100.70 | J43 | GB/T 16458.2-1996 | 磨料磨具术语 第2部分: 磨具术语 | Terminologry for abrasives and abrasive products--Part 2: Terminology for abrasives products | |
| 25.100.20 | J41 | GB/T 16459-1996 | 面铣刀寿命试验 | Tool life testing in face milling | IDT ISO 8688-1-1989 |
| 25.100.20 | J41 | GB/T 16460-1996 | 立铣刀寿命试验 | Tool life testing in end milling | IDT ISO 8688-2-1989 |
| 25.100.10 | J41 | GB/T 16461-1996 | 单刃车削刀具寿命试验 | Tool-life testing with single-point turning tools | IDT ISO 3685-1993 |
| 25.040.20 | J53 | GB/T 16462-1996 | 数控卧式车床 精度检验 | Numerically controlled turning machines--Testing of the accuracy | EQV BS 4656-1988 |
| 25.180 | Q94 | GB/T 16547-1996 | 工业窑炉用测温锥 | Pyrometric reference cones for kilns use | |
| 25.040.01 | N17 | GB/T 16642-1996 | 计算机集成制造系统体系结构 | Computer integrated manufacturing system architecture | NEQ ENV 40003 |
| 25.040.01 | N10 | GB 16655-1996 | 工业自动化系统 集成制造系统安全的基本要求 | Industrial automation systems--Safety of integrated manufacturing systems--Basic requirements | EQV ISO 11161-1994 |
| 25.040.40 | N18 | GB/T 16656.1-1998 | 工业自动化系统和集成 产品数据表达与交换 第1部分: 概述与基本原理 | Industrial automation systems and integration--Product data representation and exchange--Part 1: Overview and fundamental principles | IDT ISO 10303-1994 |
| 25.040.40 | N18 | GB/T 16656.21-1997 | 工业自动化系统与集成 产品数据的表达与交换 第21部分: 实现方法: 交换文件结构的纯正文编码 | Industrial automation systems and integration--Product data representation and exchange--Part 21: Implementation method:Clear text encoding of the exchange structure | IDT ISO 10303-21:1994 |
| 25.040.40 | N18 | GB/T 16656.31-1997 | 工业自动化系统与集成 产品数据的表达与交换 第31部分: 一致性测试方法论与框架: 基本概念 | Industrial automation systems and integration--Product data representation and exchange--Part 31: Conformance testing methodology and framework: General concepts | IDT ISO 10303-31:1994 |
| 25.040.40 | N18 | GB/T 16656.32-1999 | 工业自动化系统与集成 产品数据的表达与交换 第32部分：一致性测试方法论与框架：对测试实验室和客户的要求 | Industrial automation systems and integration--Product data representation and exchange--Part 32: Conformance testing methodology and framework: Requirements on testing laboratories and clients | IDT ISO 10303-32:1998 |
| 25.040.40 | N18 | GB/T 16656.41-1999 | 工业自动化系统与集成 产品数据表达和交换 第41部分: 集成通用资源: 产品描述与支持原理 | Industrial automation systems and integration--Product data representation and exchange--Part 41: Integrated generic resources: Fundamentals of product description and support | IDT ISO 10303-41:1994 |
| 25.040.40 | N18 | GB/T 16656.42-1998 | 工业自动化系统和集成 产品数据表达与交换 第42部分; 集成通用资源: 几何与拓扑表达 | Industrial automation systems and integration--Product data representation and exchange--Part 42: Integrated generic resources: Geometric and topological representation | IDT ISO 10303-42:1994 |
| 25.040.40 | N18 | GB/T 16656.43-1999 | 工业自动化系统与集成 产品数据表达和交换 第43部分: 集成通用资源: 表达结构 | Industrial automation systems and integration--Product data representation and exchange--Part 43: Integrated generic resources: Representation structures | IDT ISO 10303-43:1994 |
| 25.040.40 | N18 | GB/T 16656.44-1999 | 工业自动化系统与集成 产品数据表达和交换 第44部分: 集成通用资源: 产品结构配置 | Industrial automation systems and integration--Product data representation and exchange--Part 44: Integrated generic resources: Product structure configuration | IDT ISO 10303-44:1994 |
| 25.040.40 | L67 | GB/T 16656.45-2001 | 工业自动化系统与集成产品数据表达与交换 第45部分: 集成通用资源: 材料 | Industrial automation systems and integration Product data representation and exchange Part 45: Integrated generic resource: Materials | IDT ISO 10303-45:1998 |
| 25.040.40 | N18 | GB/T 16656.46-1998 | 工业自动化系统和集成 产品数据表达与交换 第46部分 集成通用资源: 可视化显示 | Industrial automation systems and integration--Product data representation and exchange--Part 46: Integrated generic resources: Visual presentation | IDT ISO 10303-46:1994 |
| 25.040.40 | L67 | GB/T 16656.47-2001 | 工业自动化系统与集成产品数据表达与交换 第47部分: 集成资源: 形状变化公差 | Industrial automation systems and integration--Product data representation and exchange--Part 47: Intergrated resources: Shape variation tolerances | IDT ISO 10303-47:1997 |
| 25.040.40 | N18 | GB/T 16656.101-1998 | 工业自动化系统与集成 产品数据表达与交换 第101部分: 集成应用资源: 绘图 | Industrial automation systems and integration--Product data representation and exchange--Part 101: Integrated application resources: draughting | IDT ISO 10303-101:1994 |
| 25.040.40 | N18 | GB/T 16656.105-1999 | 工业自动化系统与集成 产品数据表达与交换 第105部分: 集成应用资源: 运动学 | Industrial automation systems and integration--Product data representation and exchange--Part 105:Integrated application resource:Kinematics | IDT ISO 10303-105:1996 |
| 25.040.40 | N18 | GB/T 16656.201-1998 | 工业自动化系统与集成 产品数据表达与交换 第201部分 应用协议: 显式绘图 | Industrial automation systems and integration--Product data representation and exchange Part 201: Application protocol: Explicit draughting | IDT ISO 10303-201:1994 |
| 25.040.40 | N18 | GB/T 16656.202-2000 | 工业自动化系统与集成产品数据的表达与交换 第202部分: 应用协议: 相关绘图 | Industrial automation systems and integration--Product data representation and exchange--Part 202: Application protocol: Associative draughting | EQV ISO 10303-202:1996 |
| 25.040.40 | N18 | GB/T 16656.203-1997 | 工业自动化系统与集成 产品数据的表达与交换 第203部分: 应用协议: 配置控制设计 | Industrial automation systems and integration--Product data representation and exchange--Part 203: Application protocol: Configuration controlled design | IDT ISO 10303-203:1994 |
| 25.040.35 | N10 | GB/T 16657.2-1996 | 工业控制系统用现场总线 第2部分：物理层规范和服务定义 | Fieldbus standard for use in industrial control system--Part 2: Physical layer specification and service definition | IDT IEC 61158-2-1993 |
| 25.160.01 | J33 | GB/T 16672-1996 | 焊缝 工作位置 倾角和转角的定义 | Welds--Working positions--Definitions of angles of slope and rotation | IDT ISO 6947-1990 |
| 25.040.01 | L67 | GB/T 16720.1-1996 | 工业自动化系统 制造报文规范 第一部分：服务定义 | Industrial automation systems--Manufacturing message specification--Part 1: Service definition | EQV ISO 9506-1-1990 |
| 25.040.01 | L67 | GB/T 16720.2-1996 | 工业自动化系统 制造报文规范 第2部分：协议规范 | Industrial automation systems--Manufacturing message specification--Part 2: Protocol specification | EQV ISO/IEC 9506-2-1990 |
| 25.040.30 | L67 | GB/T 16720.3-1996 | 工业自动化系统 制造报文规范 第三部分：机器人伴同标准 | Industrial automation systems--Manufacturing message specification--Part 3: Companion standard for robotics | EQV ISO/IEC 9506-3-1991 |
| 25.040.01 | L67 | GB/T 16720.4-1998 | 工业自动化系统 制造报文规范 第4部分: 数值控制用伴同标准 | Industrial automation systems--Manufacturing message specification--Part 4: Companion standard for numerical control | EQV ISO/IEC 9506-4:1992 |
| 25.040.01 | J07 | GB/T 16721-1996 | 工业自动化系统 制造报文规范 协议子集规范 | Industrial automation systems--Specification of subsets of the protocol for the manufacturing--Message specification | EQV ISO/IEC TR 13345-94 |
| 25.020 | J32 | GB/T 16743-1997 | 冲裁间隙 | Blanking clearance | |
| 25.220.20 | A29 | GB/T 16744-1997 | 热喷涂 自熔合金涂层 | Thermal spraying--Self-fluxing alloy coatings | |
| 25.220 | A29 | GB/T 16745-1997 | 金属覆盖层产品钎焊性的标准试验方法 | Standard test method for solderability of metallic-coated products | |
| 25.080.01 | J50 | GB/T 16768-1997 | 金属切削机床 振动测量方法 | Metal-cutting machine tools--Measurement method for vibration | NEQ JIS B6003:1993 |
| 25.080.01 | J50 | GB/T 16769-1997 | 金属切削机床 噪声声压级测量方法 | Metal-cutting machine tools--Measurement method of sound pressure level | NEQ ISO/DIS 230:5.2 |
| 25.100.20 | J41 | GB/T 16770.1-1997 | 整体硬质合金直柄立铣刀 第1部分: 型式与尺寸 | Solid hardmetal end mills with parallel shank Part 1: Dimensions | IDT ISO/DIS 10911:1993 |
| 25.100.20 | J41 | GB/T 16770.2-1997 | 整体硬质合金直柄立铣刀 第2部分：技术规范 | Solid hardmetal end mills with parallel shank Part 2: Technical specifications | |
| 25.220.40 | A29 | GB/T 16921-1997 | 金属覆盖层 厚度测量 X射线光谱方法 | Measurement of metallic coating thickness-X--ray spectrometric methods | EQV ISO 3497:1990 |
| 25.220 | J36 | GB/T 16923-1997 | 钢件的正火与退火 | Normalizing and annealing of steel parts | EQV JIS B6911:1987 |
| 25.220 | J36 | GB/T 16924-1997 | 钢件的淬火与回火 | Quenching and tempering of steel parts | EQV JIS B6913:1989 |
| 25.160.40 | J33 | GB/T 16957-1997 | 复合钢板焊接接头力学性能试验方法 | Mechanical tests on welded joints in clad plates | |
| 25.040.30 | J07 | GB/T 16977-1997 | 工业机器人 坐标系和运动命名原则 | Industrial robots--Coordinate systems and motion nomenclature | EQV ISO 9787:1990 |
| 25.010 | J07 | GB/T 16978-1997 | 工业自动化 词汇 | Industrial automation glossary | IDT ISO/TR 11065:1992 |
| 25.040.01 | J07 | GB/T 16979.1-1997 | 工业自动化系统 制造报文规范 第1部分: 服务定义 补充件1: 数据交换 | Industrial automation systems--Manufacturing message specification--Part 1: Service definition AMENDMENT 1: Data exchange | IDT ISO/IEC 9506-1.Amd.1:1993 |
| 25.040.01 | J07 | GB/T 16979.2-1997 | 工业自动化系统 制造报文规范(MMS) 第2部分: 协议规范 补充件1: 数据交换 | Industrial automation systems--Manufacturing message specification--Part 2: Protocol specification AMENDMEN 1: Data exchange | IDT ISO/IEC 9506-2.Amd.1:1993 |
| 25.010 | J07 | GB/T 16980.1-1997 | 工业自动化 车间生产 第1部分: 标准化参考模型和确定需求的方法论 | Industrial automation--Shop floor production--Part 1: Reference model for standardization and a methodology for identification of requirements | IDT ISO/TR 10314-1:1990 |
| 25.010 | J07 | GB/T 16980.2-1997 | 工业自动化 车间生产 第2部分: 标准化参考模型和方法论的应用 | Industrial automation--Shop floor production--Part 2: Application of the reference model for standardization and methodology | IDT ISO/TR 10314-2:1991 |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.100.10 | J41 | GB/T 17111-1997 | 切削刀具--高速钢分组代号 | Cutting tools--Designation of high-speed steel groups | IDT ISO 11054:1993 |
| 25.100.30 | J41 | GB/T 17112-1997 | 定心钻 | Spot drills | IDT ISO 10898:1992 |
| 25.120.01 | J62 | GB 17120-1997 | 锻压机械 安全技术条件 | Metalforming machinery--Safety requirements | |
| 25.080 | J50 | GB/T 17161-1997 | 机床 控制装置的操作方向 | Machine tools--Direction of operation of controls | EQV ISO 447:1984 |
| 25.080 | J50 | GB/T 17162-1997 | 机床 速度和进给量 | Machine tools--Speeds and feeds | EQV ISO 229:1973 |
| 25.040.40 | N17 | GB/T 17165.1-1997 | 模糊控制装置和系统 第1部分: 基本术语 | Fuzzy control devices and systems--Part 1: Fundamental terminology | |
| 25.040.40 | N17 | GB/T 17165.2-1997 | 模糊控制装置和系统 第2部分: 模糊控制单元性能检测一般要求 | Fuzzy control devices and systems-Part 2: General requirements for evaluating performance of fuzzy control unit | |
| 25.040.40 | N17 | GB/T 17165.3-2001 | 模糊控制装置和系统 第3部分: 可编程控制器 模糊控制编程 | Fuzzy control devices and systems Part 3: Programmable controllers-fuzzy control programming | IDT IEC 61131-7-2000 |
| 25.040.40 | N17 | GB/T 17165.4-1997 | 模糊控制装置和系统 第4部分: 洗衣机模糊控制基本性能检测要求 | Fuzzy control devices and systems-Part 4: Evaluation requirements of basic properties of fuzzy control for washing machine | |
| 25.180.01 | K61 | GB/T 17195-1997 | 工业炉名词术语 | Industrial furnace terminology | |
| 25.040.01 | N10 | GB/T 17212-1998 | 工业过程测量和控制 术语和定义 | Industrial-process measurement and control--Terms and definitions | IDT IEC 60902-1987 |
| 25.040.01 | N10 | GB/T 17214.1-1998 | 工业过程测量和控制装置工作条件 第1部分: 气候条件 | Industrial-process measurement and control equipment--Operating conditions Part 1: Climatic conditions | IDT IEC 60654-1:1993 |
| 25.040.01 | N10 | GB/T 17214.3-2000 | 工业过程测量和控制装置的工作条件 第3部分: 机械影响 | Operating conditions for industrial-process measurement and control equipment Part 3: Mechanical influences | IDT IEC 606534-3:1983 |
| 25.180.01 | J66 | GB/T 17410-1998 | 有机热载体炉 | Organic heat transfer material heaters | NEQ DIN 4754-1990 |
| 25.010 | J50 | GB/T 17421.1-1998 | 机床检验通则 第1部分: 在无负荷或精加工条件下机床的几何精度 | Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions | EQV ISO 230-1:1996(E) |
| 25.040.20 | J50 | GB/T 17421.2-2000 | 机床检验通则 第2部分: 数控轴线的定位精度和重复定位精度的确定 | Test code for machine tools--Part 2: Determination of accuracy and repeatability of positioning numerically controlled axes | EQV ISO 230-2:1997 |
| 25.220.20 | A29 | GB/T 17460-1998 | 化学转化膜 铝及铝合金上漂洗和不漂洗铬酸盐转化膜 | Chemical conversion coatings Rinsed and non-rinsed chromate conversion coatings on aluminium and aluminium alloys | EQV ISO 10546:1993(E) |
| 25.220.40 | A29 | GB/T 17461-1998 | 金属覆盖层 锡--铅合金电镀层 | Metallic coatings--Electroplated coatings of tin-lead alloys | EQV ISO 7587:1986 |
| 25.220.40 | A29 | GB/T 17462-1998 | 金属覆盖层 锡--镍合金电镀层 | Metallic coatings--Electroplated coatings of tin-nickel alloys | EQV ISO 2179:1986 |
| 25.160.20 | J33 | GB/T 17493-1998 | 低合金钢药芯焊丝 | Low alloy steel flux cored electrodes for arc welding | EQV AWS A5.29-80 |
| 25.060.10 | J51 | GB/T 17587.1-1998 | 滚珠丝杠副 第1部分: 术语和符号 | Ball screws--Part 1: Vocabulary and designation | EQV ISO 3408-1:1991 |
| 25.060.10 | J51 | GB/T 17587.2-1998 | 滚珠丝杠副 第2部分: 公称直径和公称导程 公制系列 | Ball screws--Part 2: Nominal diameters and nominal leads--Metric series | IDT ISO 3408-2:1991 |
| 25.060.10 | J51 | GB/T 17587.3-1998 | 滚珠丝杠副 第3部分: 验收条件和验收检验 | Ball screws--Part 3: Acceptance conditions and acceptance tests | EQV ISO 3408-3:1992 |
| 25.040.40 | L67 | GB/T 17645.1-2001 | 工业自动化系统与集成 零件库 第1部分: 综述与基本原理 | Industrial automation systems and integration Parts library Part 1: Overview and fundamental principles | IDT ISO 13584-1:1999 |
| 25.220.40 | A29 | GB/T 17720-1999 | 金属覆盖层 孔隙率试验评述 | Metallic coatings--Review of porosity tests | EQV ISO 10308:1995 |
| 25.220.40 | A29 | GB/T 17721-1999 | 金属覆盖层 孔隙率试验 铁试剂试验 | Metallic coatings--Porosity tests--Ferroxyl test | EQV ISO 10309:1994 |
| 25.100.20 | J33 | GB/T 17853-1999 | 不锈钢药芯焊丝 | Stainless steel flux cored wires | EQV ANSI/AWS A5.22:1995 |
| 25.160.20 | J33 | GB/T 17854-1999 | 埋弧焊用不锈钢焊丝和焊剂 | Stainless steel electrodes and fluxs for submerged arc welding | EQV JIS Z3324:1988 |
| 25.040.30 | J28 | GB/T 17887-1999 | 工业机器人 末端执行器自动更换系统 词汇和特性表示 | Industrial robots--Automatic end effector exchange systems--Vocabulary and presentation of characteristics | EQV ISO 11593:1996 |
| 25.140.20 | K64 | GB/T 17952.1-2000 | 手持式市电供电圆锯性能测量方法 | Hand-held electric mains voltage operated circular saws-Methods for measuring the performance | IDT IEC 61176:1993 |
| 25.140.20 | K64 | GB/T 17952.2-2000 | 手持式市电供电喷枪的性能要求 | Hand-held electric mains voltage operated spray guns-Performance requirements | IDT IEC 61214:1993 |
| 25.100.01 | J41 | GB/T 17983-2000 | 带断屑槽可转位刀片近似切屑控制区的分类和代号 | Classification and designation of approximate chip control zones for indexable inserts with chipbreakers | IDT ISO 10910:1995 |
| 25.100.30 | J41 | GB/T 17984-2000 | 麻花钻 技术条件 | Twist drills--Technical specifications | NEQ ISO 10899:1996 |
| 25.100.10 | J41 | GB/T 17985.1-2000 | 硬质合金车刀 第1部分: 代号及标志 | Turning tools with carbide tips Part 1: Designation and marking | NEQ ISO 504:1975 |
| 25.100.10 | J41 | GB/T 17985.2-2000 | 硬质合金车刀 第2部分: 外表面车刀 | Turning tools with carbide tips Part 2: External tools | NEQ ISO 243:1975 |
| 25.100.10 | J41 | GB/T 17985.3-2000 | 硬质合金车刀 第3部分: 内表面车刀 | Turning tools with carbide tips Part 3: Internal tools | NEQ ISO 514:1975 |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
| 25.200 | J36 | GB/T 18177-2000 | 钢件的气体渗氮 | Gas nitriding of steel parts | |
| 25.220.01 | A29 | GB/T 18178-2000 | 水性涂料涂装体系选择通则 | General rules of the selection for painting system of water paint | |
| 25.220.01 | A29 | GB/T 18179-2000 | 金属覆盖层 孔隙率试验 潮湿硫(硫华)试验 | Metallic coatings--Porosity tests--Humid sulfur(flowers of sulfur) test | IDT ISO 12687:1996 |
| 25.220.40 | A29 | GB/T 18226-2000 | 高速公路交通工程钢构件防腐技术条件 | Specification for steel component anticorrosion of highway traffic engineering appurtenances | NEQ ASTM 428:1995 |
| 25.040.40 | N10 | GB/T 18271.1-2000 | 过程测量和控制装置--通用性能评定方法和程序 第1部分: 总则 | Process measurement and control devices--General methods and procedures for evaluating performance--Part 1: General considerations | IDT IEC 61298-1:1995 |
| 25.040.40 | N10 | GB/T 18271.2-2000 | 过程测量和控制装置--通用性能评定方法和程序 第2部分: 参比条件下的试验 | Process measurement and control devices--General methods and procedures for evaluating performance--Part 2: Tests under reference conditions | IDT IEC 61298-2:1995 |
| 25.040.40 | N10 | GB/T 18271.3-2000 | 过程测量和控制装置--通用性能评定方法和程序 第3部分: 影响量影响的试验 | Process measurement and control devices--General methods and procedures for evaluating performance--Part 3: Tests for the effects of influence quantities | IDT IEC 61298-3:1998 |
| 25.040.40 | N10 | GB/T 18271.4-2000 | 过程测量和控制装置--通用性能评定方法和程序 第4部分: 评定报告的内容 | Process measurement and control devices--General methods and procedures for evaluating performance--Part 4: Evaluation report content | IDT IEC 61298-4:1995 |
| 25.040 | N10 | GB/T 18272.1-2000 | 工业过程测量和控制--系统评估中系统特性的评定 第1部分: 总则和方法学 | Industrial-process measurement and control--Evaluation of system properties for the purpose of system assessment Part 1: General consideration and methodology | IDT IEC 61069-1:1991 |
| 25.040 | N10 | GB/T 18272.2-2000 | 工业过程测量和控制--系统评估中系统特性的评定 第2部分: 评估方法学 | Industrial-process measurement and control--Evaluation of system properties for the purpose of system assessment Part 2: Assessment methodology | IDT IEC 61069-2:1993 |
| 25.040 | N10 | GB/T 18272.3-2000 | 工业过程测量和控制--系统评估中系统特性的评定 第3部分: 系统功能性评估 | Industrial-process measurement and control--Evaluation of system properties for the purpose of system assessment Part 3: Assessment of system functionality | IDT IEC 61069-3:1996 |
| 25.040 | N10 | GB/T 18272.5-2000 | 工业过程测量和控制--系统评估中系统特性的评定 第5部分: 系统可信性评估 | Industrial-process measurement and control--Evaluation of system properties for the purpose of system assessment Part 5: Assessment of system dependability | IDT IEC 61069-5:1994 |
| 25.040.10 | J54 | GB/T 18400.6-2001 | 加工中心 检验条件 第6部分：进给率、速度和插补精度检验 | Test conditions for machining centres--Part 6: Accuracy of feeds, speeds and interpolations | EQV ISO 10791-6:1998 |
| 25.040.10 | J54 | GB/T 18400.8-2001 | 加工中心 检验条件 第8部分：三个坐标平面上轮廓特性的评定 | Test conditions for machining centres--Part 8: Evaluation of the contouring performance in the three coordinate planes | EQV ISO/DIS 10791-8 |
| 25.160.30 | J64 | GB/T 18495-2001 | 电阻焊 与焊钳一体式的变压器 | Electric resistance welding--Integrated transformers for welding guns | EQV ISO 10656:1996 |
| 25.180.10 | K61 | GB/T 18497.1-2001 | 工业加热用电红外辐射器的特性 第1部分: 短波电红外辐射器 | Characteristics of electric infra-red emitters for industrial heating Part 1: Short wave infra-red emitters | IDT IEC 60240-1:1992 |
| 25.040.10 | J50 | GB 18568-2001 | 加工中心 安全防护技术条件 | Machining centres--Safeguarding specification | |
| 25.220.10 | A29 | GB/T 18570.2-2001 | 涂覆涂料前钢材表面处理 表面清洁度的评定试验 清理过的表面上氯化物的实验室测定 | Preparation of steel substrates before application of paints and related products--Tests for the assessment of surface cleanliness--Laboratory determination of chloride on cleaned surfaces | EQV ISO 8502-2:1992 |
| 25.220.10 | A29 | GB/T 18570.4-2001 | 涂覆涂料前钢材表面处理 表面清洁度的评定试验 涂覆涂料前凝露可能性的评定导则 | Preparation of steel substrates before application of paints and related products--Tests for the assessment of surface cleanliness--Guidance on the estimation of the probability of condensation prior to paint application | EQV ISO 8502-4:1993 |
| 25.160.10 | J33 | GB/T 18591-2001 | 焊接 预热温度、道间温度及预热维持温度的测量指南 | Welding--Guidance on the measurement of preheating temperature,interpass temperature and preheat maintenance temperature | IDT ISO 13916:1996 |
| 25.220.40 | A29 | GB/T 18592-2001 | 金属覆盖层 钢铁制品热浸镀铝 技术条件 | Metallic coating--Hot dipped aluminum coatings on ferrous articles--Specification | |
| 25.220.60 | A29 | GB/T 18593-2001 | 熔融结合环氧粉末涂料的防腐蚀涂装 | Anti-corrosive painting of fusion bonded epoxy coating powders | |
| ICS 国際規格分類 |
中国標準分類 | 規格番号 | 規格名称(中国語) | 規格名称(英語) |
国際整合 |
ご意見、ご要望、ご質問 は、